3.1 Classification of fuels | unit 3 fuels

CHEM

Unit 3

Fuels

3.1 Classification of fuels

Chemical fuels are classified on the basis of occurrence into :-

Primary ( natural )

Secondary ( derived ) types / manmade .

The secondary fuels are obtained from primary fuel by processing or they are manmade. e.g.:- charcoal is obtained from wood by partial combustion of wood , ethyl alcohol is obtained by fermentation of carbohydrates .

Both the primary and secondary fuels are further classified on the basis of physical state into solid liquid and gaseous fuels.

Extra definitions :-

1] fuels :-

Fuels are defined as materials that create usable energy through chemical nuclear or electrochemical reaction.

2] chemical fuel :-

The fossil fuels , wood vegetal oils etc. . which produce heat on burning are known as chemical fuels.

3.2 Calorific value. (Determination by Dulong’s formula)

Calorific value :- efficiency of combustible fuels can be measured in terms of their calorific value . it is the heat evolved on combustion of a unit quantity of fuel.

Definition of calorific value :-

It is defined as the amount of heat obtained on complete combustion of unit mass of a solid or liquid fuel or unit volume of a gaseous fuel at STP.

3.3 G.C.V. and N.C.V

Usually fuel contains some hydrogen . the hydrogen atoms are bonded to carbon atoms in the fuel when the fuel is burnt , hydrogen forms water vapors . the water vapors if cooled , we get certain amount of heat as the water has high latent heat of 2450 joules / gm or 587 Cal / gm.

Thus, during the study of calorific value of a fuel we get some heat directly by combustion of fuel and in addition we get certain amount of heat by cooling the products of combustion to 15-degree c.

Gross calorific value :-

Gross calorifia value of a fuel can be defined as the total amount of heat obtained on complete combustion of unit mass of a solid or liquid fuel or unit volume of a gaseous fuel ( S T P ) and on cooling the products of combustion to 15 degree c . the gross calorific value is also called as higher calorific value.

The G.V.C is of only theoretical importance because in actual practice we do not have any provision of cooling the products of combustion during combustion of fuel in an engine , furnace or any other fuel burning device.

Net calorific value :-

A fuel contain hydrogen produces water heat and actually less heat is available for heating.

There is not any furnace , engine or device designed to collect the heat being taken away by the water vapors . therefore, practically we get lower calorific value than the theoretical expected.

Net calorific value :-

Net calorific value is defined as the amount of heat obtained practically on complete combustion of unit mass of solid or liquid fuel or unit mass of solid or liquid fuel or unit volume of a gaseous fuel at step and the products of combustion are allowed to escape with some heat N.C.V is also called as lower calorific value.

The N.C.V and G.C.V are related as under

G.C.V = N.C.V + )

Where h is the percentage of hydrogen in the fuel.

It should be noted that the unit of latent heat of water and unit of G.V.C , N.C.V should be same .

Units of calorific value :-

System	Solid or liquid fuel	Gaseous fuel
CGS	Cal / gm	Cal / liter
MKS	Kcal / kg	Kcal /
S.I	Joules / kg	Joules /

3.4 Solid fuels

Solid fuels :- coal

Coal is highly carbeanous matter formed vegetable matter buried in geomorphic changes , under pressure , by action of aerobic and anaerobic bacteria for long time.

1. the time for transformation wood to coal depends upon the depth of the burial.

The processes of conversion of wood into coal is known as coalification.

In general coal contains mainly carbon atoms with mostly sp² hybridization. Atoms like O , H , S , N are covalently bonded to carbon atoms . coal also contain water and mineral particles entrapped.

When coal start burning , some of the heat produced is utilized to evaporate water and minerals are left behind . as ash ( metal oxidize , silica )

The volatile matter is the unburnt decomposed coal molecules fragments of colloidal size.

Classification of coal ( types / grades ):-

The conversion of wood ( plant matter ) into coal takes place progressively . depending upon the extent of transformation coals are divided into 4 types or grades or ranks.

During the progressive conversion from peat to anthracite there is,

Increase in carbon percentage calorific value , density luster , hardness , black color intensity decreases in – moisture , volatile , matter .

Peat :-

Peat is brown and fibrous in texture .

Freshly mined out peat contains large quantity of water as it is found in waterlogged areas.

Air dried peat contains 15 – 25 percent moisture and it crumbles into powder during air drying.

Calorific value of peat is about 5400 Cal / gm.

It has low density

It contains 57 percent c , 61 percent c .

Uses :-

Peat type of coal gets powdered during combustion ;therefore, it is used after briquetting as domestic and industrial fuel.it is used for soil conditioning

On carbonization ( heating in absence of air ) at 5000° c it produces char oil light spirits.

It can be used for steam raising , thermal insulation packing gas purification and sometimes for power generation.

Lignite :-

It is intermediate stage between peat and black coal.

It is brownish black and more compact than peat.

It contains 45 – 50 percent volatile matter and burns with log flame.

Its C.V id about 6000- 6700 Cal / gm and c percent it is 65 – 70 percent .

It contains 5 percent H 20 percent O.

Uses :-

After briquetting it is used as domestic and industrial fuel.

Bituminous coal :-

This type of coal burn with smoky yellow flame and are dark – grey to black they contain 70 – 90 percent c and therefore they are classified as

Sub – bituminous coal :-

This coal has character’s between lignitc and bituminous coal.

It is harder and denser than lignite .it is grey black and has dull waxy lusture.

Its C.V is about 7000 Cal / gm and 70 – 75-degree c. it contains large volatile matter 35 – 40-degree c.

It crumbles into pieces on air drying and during transportation .it is non caking.

This coal is used for domestic and insulation purpose.

2. Bituminous coal :-

This coal has banded or laminated structure with alternate bright and dull layers.

It has cubical fracture.

It is black dense and hard.

It contains 75 – 85 percent c and has c.v 8000-8500 Cal / gm

It is a caking coal and forms coke and coal gas on carbonization , as it contains 20 – 30 percent volatile matter.

3. Semi bituminous coal :-

It has characters between bituminous and anthracite coals.

It has low volatile matter and caking property.

( caking – coal decomposing at about 400°c melting forming a plastic mass through which U.M blows out forming highly swollen open structured coal called as coke )

Its c.v is about 8400 Cal / gm .

Uses :-

Making of coke , high temperature heating , coal gas for tar and chemicals.

4. Anthracite coal :-

This is highest rank or grade coal

It has C.V about 8700 coal / gm and 92 – 98-degree c.

It is highly lustrous black and hard coal.

It burns with non – smoky short blue flame of high temperature.

Uses :-

Costly coal it is used for specific industrial purposes.

It used as metallurgical fuel

It is used for making electrodes

It is used for high temp heating’s

Analysis of coal :-

Coal is mainly composed of C , h , N , S moisture volatile matter.

The purpose for coal analysis is

to decide price of coal

to determine quality

to specify use of coal for a particular purpose

to calculate theoretical calorific values of coal

to calculate air requirement for complete combustion of coal and design the furnace fire box suitably.

A sample of coal taken out from coal mine is analyzed in two ways.

Proximate analysis

Ultimate analysis

Proximate analysis of coal ( 5 / 6 m )

Proximate analysis is the study or analysis of coal sample in which

Moisture ( percent )

Volatile matter ( percent )

Ash ( percent )

Fixed carbon ( percent ) are found out

A] moisture ( percent ) :-

A known weight of powdered and air-dried coal sample is taken in a crucible and it is placed in an oven for 1 hour at 110°c .

Then the coal it is placed in a dedicator and weighed out.

If the initial weight of the coal is m gms and final weight m gms .the loss in weight ( m – m1 ) corresponds to moisture in coal.

Moisture percent = *100

B] volatile matter (V.M) :-

Moisture free coal left in the crucible in first experiment ( m1 ) is covered with a lid loosely . then it is heated at 925° c in a muffle furnace for 7 minutes .

The crucible is taken out and cooled in a desiccator.

Then it is weighed ( m2gms ) the loss in weight ( m1 –m2 ) is due to loss of volatile matter in m gms of the coal sample. ( volatile matter is the lower molecular weight organic compound in a coal and decomposed coal during burning of coal , that escapes without combustion , in the forms of smoke )

Volatile matter (percent ) :-

The volatile matter percent can be also determined by taking the fresh weight of the air dried coal but the loss in weight .at 925°c will be due to loss of moisture and volatile matter if W is the mass of coal left at 925° c heating,

Then ,

Volatile matter percent = *100

= – moisture percent

C] Ash percent :-

The residual coaling the above experiment is heats and weighed (n m3 gm)

Therefore ,

Ash ( percent ) * 100 = *100

D] fixed carbon ( percent ) :-

It is found by calculation

f.c = 100 – ( moisture + v.m + ash )

significance ( important of proximate analysis )

Moisture :-

Decrease calorific value of coal largely as it does not burn and take away heat in the form of latent heat.

It increases ignition point of coal.

It increases ignition point of coal hence, a coal with lower moisture is better quality.

Volatile matter :-

It decreases calorific value of coal.

It elongates flame and decrease flame temp

It forms smoke and pollutes air

However , the coals containing 15 – 25 percent of X.M on carbonization gives coke oven gas which is the source of various organic aromatic chemicals such coals have good caking property and caking the coals be obtained from the coals.

Overall , regarding burning of coal the coal the coal with lesser V.M is better quality coal.

Ash :-

Ash reduces C.V of coal as ash is non – burning part in coal.

Ash disposal is a problem

Ash fuses to form clinker at high temperature obstructing the air supply to coal burning in.

Principle of ash :-

Inorganic matter in the coal gets oxidized to form metal oxides coal get oxidized to form metal oxidize and silica which is non – combustible and left as ash.

D ] fixed carbon :-

Carbon is the burning part in coal and high the fe higher C.V hence a good quality coal containing high FC ( percent )

f.c( percent ) = 100 – ( moisture + V.M + ash )

numerical :-

Compute the proximate analysis results 1.9 gms of a coal sample loses 0.285gm weight at 110°c.

1.5 gm of the same coal sample loses 0.36gm weight at 925°c.

2.15 gms of the coal sample leaves 0.26 gm ash.

Given data :-

M=1.9 gm

( m – m1 )= 0.285 gm ( moisture loss )

Loss in weight due to moisture and VM = 0.36gm

Weight of coal = 2.15 gm

Weight of ash = 0.26gm

Moisture ( percent ) =

*100

= = 15 percent

2. V.M ( percent ) :-

v.m = *10

= *100-15 = 24 – 15

= 9 percent

3. Ash ( percent ) :-

Therefore ,

Ash =

= 12 ( percent )

Principle :-

The C in the coal gets converted co2 and hydrogen to h2o vapors burning in the presence of pure o2

Ultimate analysis of coal :-

The analysis of coal in which percentage of C , N , H , S and O elements are found out is known as ultimate analysis .

A] C,H in coal :-

A known weight of powdered and air-dried coal sample is burnt in the presence of pure oxygen in a combustion apparatus C and H are converted to CO2 and H2O vapors respectively

The gaseous products are allowed through first the pre-weighed u – tube containing any hydrous crack ( absorbing H2O vapors and through the KaH solution in a pre-weighed u – tube ( absorption of co2 )

The increase in weight of u – tube containing any hydrous Cacl2 corresponds to weight of water formed and increase in weight of u – tube containing KoH solution corresponds to co2 formed by combusting the coal sample .

C + O2 – CO 2

2H + ½ - H2O

2KoH + CO2 – K2CAO3 + H2O

Cacl2 + 7H2O – Cacl2 – CacL2 .7h20

N ( percent ) – n in coal gets converted to anomnoussulphate by action of hot conc . H2SO4 and then on treatment with alkali solution.

C ( percent ) =

H ( percent ) =

B] nitrogen in coal :-

A known weight of powdered and air-dried coal is heated with concentrated H2SO4 along with K2So4 catalyst in a long necked kjeldahls flask.

After the contents become clean it is treated with alkali solution in a round bottom flask the ammonia ( basic gas ) liberated is passed in a round bottom flask the ammonia ( basic gas ) liberated is passed in known volume of std. acid solution.

The unused acid is determined by titration with NaOH solution.

Mass of coal = M gms

Volume of X N acid in which NH3 is passed

Volume of acid unused = V2ml

Volume of the acid consumed by NH3 = ( V1 – V2 ) ml

N ( percent ) =

C] Sulphur in coal :-

Take out 10 ml of distilled water in the bomb pot .burn the known weight of powdered and air-dried coal sample in the bomb calorie meter experiment .

The collect the washing of bomb pot in a beaker add Bacl2 solution in it.

Filter the precipitate of Baso4 from weight of Baso4 precipitate , calculate as below :-

S ( percent ) =

Ash :- as carried out as under proreimate analysis

O :- it is obtained by difference

Importance of ultimate analysis:-

Carbon :-

Greater than percent of carbon in coal better is the coal quality and c.v

Hydrogen :-

Most the hydrogen in coal is in the form of moisture and volatile matter only a small percentage of hydrogen is combustible hence it decreases c.v of coal . smaller the H better is the coal quality.

Nitrogen :-

Nitrogen does not burn during coal combustion and therefore, it has no calorific value hence a good quality coal has negligible N.

Sulphur :-

Although Sulphur can burn and increase calorific value of coal, but it causes so pollution and cause acidic rain corrosion of metallic equipment hence lower the percent of s in coal better is a coal quality.

Oxygen :-

Most of the oxygen in coal is in the form of moisture .

It decreases calorific value of coal ( 1 percent oxygen in coal decrease c.v by 1.7 hence, lower the o percent better is coal quality . )

3.5 Analysis of coal

Calculate C , N , H , S from the following observation for a sample of coal.

2.05 gms of the coal is burnt in combustion tube. The increase in weight of any hydrous Cacl2 is 0.55 gm and increase in weight of KoH tube is 5.75gm.

0.75 of the coal is kjaldahl experiment released NH3 which is passed in 50ml 0.12 N NaoH to neutralize in back titration.

Washings of the bomb pot when 1.8 gm.

Given data :-

Increase in weight of any hydrous calcl2 = 0.55

Mass of coal = 0.75gms

Volume of 0.12 NHCL consumed by NH3 = 50 – 41

= 9 ml

Mass of coal = 1.8gms

Weight of Baso4 = 0.31 gm

Weight of CO 2 formed = increase in wt. OfKoH

Therefore ,

C percent ) = **100 = 76.5 percent .

Increase in weight of any hydrous Cacl2

= weight of H2O formed

Mass of coal = 2.05gm

H ( percent ) = **100

= 2.98 ( percent )

2. N ( percent ) =

= 2.02 ( percent )

3. S ( percent ) = *100

= 2.36 ( percent )

Theoretical calorific values

A] gouthal formula :-

Theoretically calorific value of coal can be calculated from proximate analysis data by using gouthal formula .

G.C.V Cal / gm = 82fc + a.VM

The values of constant are as under

3.6 Liquid fuels: Classification of petroleum

Petroleum :-

Petroleum or crude oil is a dark greenish brown viscous liquid in earth crust at the depth of few meters to 7kms.

Crude oil is the most important source of various liquid fuels used now and a large number of petrochemicals can be manufactured ( plastics , rubber , fibers , medicine ) from the crude oil fractions.

Origin of petroleum :-

As per modern theory petroleum is formed from buried debris of plants and animals ( organic matter ) under favorable conditions.

The burial of the organic matter during volcano upheavals. In earth surface should take place along with large quantity of water and under a dome of hard , impervious rock.

An aerobic bacteria , higher temperature , radioactive matter makes the degradation of organic matter , in the presence of water , under the dome to highly alkanes rich matter as crude oil.

The anaerobic bacteria take out oxygen atoms from cellulose protein oil molecules and forms alkenes rich crude oil

E.g. –

Prolonged action of higher temperature and action of radioactive substances cause the breaking very long hydrocarbon molecules to smaller during the ages of time , the hydrocarbon molecule.

Crude oil is always deposited on the layer of salty water and above crude oil layer there is natural gas consisting of C1 TO C4 hydrocarbons and NH3 , H2S , CO , moisture.

Composition of petroleum :-

Average elemental composition of petroleum crude oil is,

C = 80 -87 percent

H= 11 to 15 percent

O = 0.1 to 0.9 percent

S = 0.1 to 3 percent

N = 0.4 to 0.9 percent

Petroleum contains following type of compounds :-

1) Open chain alkanes

2) Cycloalkanes

3) Aromatics

4) Asphaltenes

5) Resins

Open chain alkenes :-

Both straight chain and branched alkanes are present in crude oil. In some crude oil such alkenes are major part.

Aromatics :-

In all the crude oils benzene and alkyl substituted benzenes are up to 2 percent.

Asphaltenes :-

All the crude oil contains small amount of poly condensed aromatic solid as colloidal dispersion in crude oil .the asphaltenes also contain N ,S , O atoms.

Resins :-

These are polymeric substances .they are gummy and are lower molecular weight polymers . they are also containing N , S , O atoms .

All the crude oil contain little amount of emulsified water is rich with dissolved salts.

The number of carbon atoms in hydrocarbon molecules range from C1 TO C70 in crude oil.

Refining of petroleum :-

Crude oil cannot be directly used for any purpose .refining or fractionation is the processes of separation of various fraction from crude oil , on the basis of fractional distillation .

The crude oil contains a large number of hydrocarbon but by the processes of refining they are divided into few groups of mol.wt or boiling point ranges.

They are as follows :-

Removal of water

Removal of Sulphur

Fractionation

Removal of water :-

First the emulsified water along with salts dissolved is removed by passing the crude oil between highly charged electrodes .The colloidal water droplets unite to form large drops which separate from oil.

Removal of Sulphur :-

Then the crude oil is treated with hot to remove .Sulphur from the Sulphur compound in crude oil.

Fractionation :-

The principle of fractional distillation is that the vapors of higher boiling point compounds get condensed into liquid , during the stepwise cooling.

Construction :-

The refining is carried out in a tall cylindrical tower called as fractionating column .the fractionating column is a tall cylindrical stainless-steel tower about 30 m in height and 3 m in diameter.

There are 50 -60 horizontal stainless trays at about half meter distances in the tower. Each dry is provided with 4-5 bubble cups with loose caps so that the raising vapors through the cap bubble in the liquid deposited on tray.

Temperature of the tower is 400° c near bottom, and it decrease gradually to 40°c atop .

The tower is cooled by open air.

Working :-

The crude oil is heated at 400°c in a furnace or pipe still to convert it into vapors.

The vapors travel upwards through the bubble caps and gradually get cooled the vapors of organic compounds with higher b.p get condensed in bubble caps and the liquid deposits on the trays.

The uncondensed vapors rise up and get condensed turn by turn on upper bubble trays. There is vigorous bubbling action on each tray. In case large part of the vapors get condensed on a tray .then the extra liquid flow down to higher temp. lower trays and gets evaporated.

From some bubble trays the fractions like petrol d, diesel , kerosene , naphtha , heavy oil etc. are taken out. Finally, a small of vapors comes out as uncondensed gases from the top where temp. is about 40 ° c.

Heavy oil fraction can be further to get lubricating oils , Vaseline wax.

The petrol obtained from refinery is called as straight run petrol but is not a good quality petrol.

It is possible to convert any higher boiling fraction to convert into petrol or LPG by the processes know as cracking .

3.7 Refining of petroleum

The various petroleum fraction has calorific value about 1100 Cal / gm .their composition, boiling range and uses are given.

Name of fraction	Boiling range	Composition of HC	uses
Uncondensed gases	Below 40 ° c	C1 to c4	Domestic and industrial fuel under lpg name
2. Petroleum ether	40-70° c	C5 to c7	Fuel for Aeroplan helicopter as solvent
3. Petrol or gasoline	60-120° c	C5 to c8	Fuel for petrol engines dry cleaning as solvent.
4. Naphtha or solvent spirit	120 -180 ° c	C7 to C10	For dry cleaning for chemicals
5. Kerosene	180-250° c	C10 TO C16	For domestic fuel for oil gas.
6. Diesels	250 - 320° c	C15 to c18	Diesel engine fuel
7. Heavy oil	320-400° c	C18 – c20	Lubricating purpose
8. residue		Above C30	Road making water proofing

3.8 Unleaded petrol, synthetic petrol, power alcohol

Power alcohol

Definition :-

When ethyl alcohol is used as fuel internal combustion engine .it is called as power alcohol . combustion engine it is called as power alcohol generally , ethyl alcohol is used as its 5 – 25 percent mixture with petrol.

India has started mixing 5 percent ethyl alcohol in petrol from year 2003 but countries like brazil use 25 percent .ethyl alcohol in petrol from 1970.

Use of ethyl alcohol is petrol reduces our dependence for petrol on foreign reserves by about rs 5000 annum. Further it gives boost to the indigenous manufactures of ethyl alcohol and farmers get better price of their grain produce .

Ethyl alcohol is mainly manufactured by fermentation of molasessstretch .carbohydrates on a large scale and cheaply . it can also be obtained from synthesis of gas ( co , H2 ).

Reactions :-

4. The starch or sucrose in molasses is converted into ethyl alcohol by fermentation as in above reactions the ethyl alcohol obtained contains 95.5 percent alcohol is separated by use of suitable dehydration agent or by distilling it along with benzene .

Advantages of power alcohol :-

Ethyl alcohol has very good anti knocking property and its octane number is go , while the octane number of petrol is about 65 ( percent ).

Therefore, addition of ethyl alcohol to petrol increases its octane number.

2. Alcohol has property of absorbing any traces of water if present in petrol.

3. If a specially designed engine with higher compression ratio is used, then the disadvantage of lower c.v of ethyl alcohol can be overcome.

4. Ethyl alcohol contains O atoms which help for complete combustion of power alcohol and the polluting emissions of co , hydrocarbon is reduced largely.

5. Use of ethyl alcohol in petrol reduces our dependence on foreign countries for petrol and saves foreign currency considerably.

6. Power alcohol is cheaper than petrol.

Disadvantages :-

Ethyl alcohol has c.v 7000cal /gm . use of power alcohol reduces power output up to 35 ( percent )

2. Ethyl alcohol has high surface tension and its atomization especially at lower temperature is difficult causing starting trouble.

3. Ethyl alcohol may undergo oxidation to form acetic acid which corrodes engine parts .

4. Ethyl alcohol obtained by fermentation processes directlycannot be mixed with petrol, but it has to be dehydrated first.

5. Prepare sodium methoxide from sodium metal and methanol .add the sodium methoxide about 2 percent by weight to vegetable oil or fat.

6. Add methanol about 20 percent by volume to the mixture .

7. Heat the mixture with stirring for 30 min

8. Cool and mix sufficient water stir well the glycerol and soap dissolve in water phase .

9. Separate the water insoluble phase from water phase

10. Add antioxidant to the biodiesel to avoid it to become gumany due to oxidation and polymerization.

Biodiesel can be obtained from various vegetable oils like soya beenoil ,palm oil , groundnut oil , cottonseed oil , mustard oil , flower oil , etc. . and also, from the animal fats .

The product is given name biodiesel on account of that it is obtained from biological product and It is biodegradable material.

Advantages of biodiesel:-

Biodiesel can be used as a good fuel for diesel engine but generally it is used as its 20 percent mixture with diesel.

Biodiesel is cheaper

2. It has high c.v of about 40 kg / gm

3. It is regenerative and environmentally friendly .

4. It does not give out particulate and CO pollutants .

5. It has certain extent of lubricity

6. It uses provided good market to vegetable oils and reduces our dependence on biodiesel onforeign countries , saving currency.

7. It is clean to use biodiesel in diesel engine .

Power alcohol

Definition :-

India has started mixing 5 percent ethyl alcohol in petrol from year 2003 but countries like brazil use 25 percent .ethyl alcohol in petrol from 1970.

Ethyl alcohol is mainly manufactured by fermentation of molasessstretch .carbohydrates on a large scale and cheaply . it can also be obtained from synthesis of gas ( co , H2 ).

Reactions :-

Advantages of power alcohol :-

Ethyl alcohol has very good anti knocking property and its octane number is go , while the octane number of petrol is about 65 ( percent ).

Therefore, addition of ethyl alcohol to petrol increases its octane number.

2. Alcohol has property of absorbing any traces of water if present in petrol.

3. If a specially designed engine with higher compression ratio is used, then the disadvantage of lower c.v of ethyl alcohol can be overcome.

4. Ethyl alcohol contains O atoms which help for complete combustion of power alcohol and the polluting emissions of co , hydrocarbon is reduced largely.

5. Use of ethyl alcohol in petrol reduces our dependence on foreign countries for petrol and saves foreign currency considerably.

6. Power alcohol is cheaper than petrol.

Disadvantages :-

Ethyl alcohol has c.v 7000cal /gm . use of power alcohol reduces power output up to 35 ( percent )

2. Ethyl alcohol has high surface tension and its atomization especially at lower temperature is difficult causing starting trouble.

3. Ethyl alcohol may undergo oxidation to form acetic acid which corrodes engine parts .

4. Ethyl alcohol obtained by fermentation processes directlycannot be mixed with petrol, but it has to be dehydrated first.

5. Prepare sodium methoxide from sodium metal and methanol .add the sodium methoxide about 2 percent by weight to vegetable oil or fat.

6. Add methanol about 20 percent by volume to the mixture .

7. Heat the mixture with stirring for 30 min

8. Cool and mix sufficient water stir well the glycerol and soap dissolve in water phase .

9. Separate the water insoluble phase from water phase

10. Add antioxidant to the biodiesel to avoid it to become gumany due to oxidation and polymerization.

Biodiesel can be obtained from various vegetable oils like soya beenoil ,palm oil , groundnut oil , cottonseed oil , mustard oil , flower oil , etc. . and also, from the animal fats .

The product is given name biodiesel on account of that it is obtained from biological product and It is biodegradable material.

Advantages of biodiesel:-

Biodiesel can be used as a good fuel for diesel engine but generally it is used as its 20 percent mixture with diesel.

Biodiesel is cheaper

2. It has high c.v of about 40 kg / gm

3. It is regenerative and environmentally friendly .

4. It does not give out particulate and CO pollutants .

5. It has certain extent of lubricity

6. It uses provided good market to vegetable oils and reduces our dependence on biodiesel onforeign countries , saving currency.

7. It is clean to use biodiesel in diesel engine.

3.9 Gaseous Fuel: Producer gas, Water gas, LPG, CNG, Kerosene gas

Natural Gas is a fossil fuel. It occurs naturally and approximately consists of 95% hydrocarbon methane, the other 5% consists of nitrogen, carbon dioxide, helium or hydrogen sulfide. It takes millions of years for it to form.

The gas is formed when layers of decaying plants and animals are buried under the earth’s surface and are exposed to intense heat and pressure for millions of years. Plants originally obtain energy from the sun and store in the form of chemical bonds in the gas. And thus, the formation of this gas occurs.

Properties:

The state of matter of this gas is gaseous.

It doesn’t have any color and is a tasteless gas.

It is free of any kind of toxic, there is no smoke on burning and it has high calorific value.

The gas is odourless. However, a chemical called mercaptan is added to it in small amounts to give it distinctive smell of eggs. This helps to find out any gas leaks.

It is a combustible gas and a fossil fuel.

Its a mixture of simple hydrocarbon compounds.

It contains primarily methane, along with small amounts of ethane, butane, pentane, and propane.

The by-products of this gas are water vapor and carbon dioxide.

Air is 60% heavier than natural gas.

It has a low flammability range and a high ignition temperature.

Generally, it is transported through pipes.

It occurs naturally in the rocks beneath the earth’s surface, in sedimentary rocks that are porous.

Applications

It is used in vehicles in the form of CNG (Compressed Natural Gas).

It is also used to manufacture a few chemicals and fertilizers.

The gas is used as a source of energy for cooking, heating, and electricity generation.

It is used as chemical feedstock for manufacturing plastic and other commercially important organic chemicals.

The gas is also useful in the production of fabrics, glass, paint, plastic, steel, etc.

Hydrogen can also be produced with the help of it.

Protein-rich animal and fish feed is produced by feeding this gas on a commercial scale.

Hydrogen gas as a future fuel

The main purposes to produce green hydrogen is to add it to the natural gas system, because the natural gas system is seen as a seasonal and large energy storage and necessary for balancing the intermittent electricity production from renewable wind and solar. When hydrogen is mixed with natural gas, the hydrogen content can vary in a wide range. Gas engines have the capability to burn gases with a wide range of hydrogen content, but there are also some challenges with a potentially high fluctuation of the hydrogen content or fast rate of change.

The two technology areas, traffic decarbonisation and long-term energy storage, depend on H2. As H2 will be transported in pipelines, the need for flexible H2-tolerant gas engines will rise.

3.10 Alternative fuels: Power alcohol and biodiesel.

Power alcohol

Definition :-

India has started mixing 5 percent ethyl alcohol in petrol from year 2003 but countries like brazil use 25 percent .ethyl alcohol in petrol from 1970.

2. Use of ethyl alcohol is petrol reduces our dependence for petrol on foreign reserves by about rs 5000 annum. Further it gives boost to the indigenous manufactures of ethyl alcohol and farmers get better price of their grain produce .

3. Ethyl alcohol is mainly manufactured by fermentation of molasessstretch .carbohydrates on a large scale and cheaply . it can also be obtained from synthesis of gas ( co , H2 ).

Reactions :-

Reference Books

1. Inorganic Chemistry by Donald A. Tarr, Gary Miessler, Pearson India, Third Edition.

2. Quantum Chemistry by Ira N. Levine, Pearson 7th Edition.

3. Molecular Spectroscopy, Ira N. Levine, John Wiley and Sons

4. Modern Spectroscopy – A Molecular Approach, by Donald McQuarrie and John Simon, published by University Science Books.

7. Inorganic Chemistry by W.Overton, Rounk and Armstrong, Oxford Univesity Press, 6th edition.

8. Introductory to Quantum Chemistry by A. K. Chandra. , 4th Edition, McgrawHill Education.

Sign Up

Index

Notes

Highlighted

Underlined

Browse by Topics

Notes

Highlighted

Underlined