Unit-1
Fluid
A fluid is a substance which can flow under the action of shear force (however small force may be).
Example- Liquid, gases, vapour.
For a static fluid, shear force is zero.
Figure 1: Force at static fluid
Solid regains their original shape if the shear force within elastic limit when the force is removed. But fluid never regains original shape after the removal of force.
S.I. Unit of Surface tension is N/m
The dimensional formula of surface tension is MT-2.
According to Newton’s law of viscosity the shear stress is directly proportional to rate of shear strain or rate of angular deformation or velocity gradient. The fluid which follows this is law is called newtonion fluid.
Newton’s law of viscosity is similar to hooke’s law for solid.
Figure 2: Diagram for newton’s law of viscosity
There are various properties of fluid. Some of them are mentioned below:
It is defined as the ratio of mass of the fluid to its volume. Its unit is kg/m3 and its dimensional formula is ML-3.
Density depends on temperature and pressure.
Specific volume is defined as the ratio of volume of fluid to the mass of fluid.
It is denoted by Vs.
Mathematically it is denoted as
Vs=V/m=1/
It is defined as the ratio of density of fluid to the density of standard fluid.
Or
It can be defined as the ratio of specific weight of fluid to the specific weight of standard fluid.
It is unit less or dimensionless.
For liquid, the standard fluid is water and for gases the standard fluid is either H2
Or air at given temperature and pressure.
The specific gravity of water is 1.
If the specific gravity of liquid is less than 1 that means it is lighter than water and if the specific gravity of liquid is greater than 1, it means the liquid is heavier than water.
It is the internal resistance offered by one layer fluid to the other layer.
Figure 3: Viscosity diagram
As the tandθ is very less, then
we know that, shear stress= shear force/shear area
As the molecules are taken into same area:
“Surface tension is the tension of the surface film of a liquid caused by the attraction of the particles in the surface layer by the bulk of the liquid, which tends to minimise surface area”.
Surface tension is the tendency of liquid surfaces to shrink into the minimum surface area possible. Surface tension allows insects (e.g. water striders), to float and slide on a water surface without becoming even partly submerged.
At liquid–air interfaces, surface tension results from the greater attraction of liquid molecules to each other (due to cohesion) than to the molecules in the air (due to adhesion).
There are two primary mechanisms in play. One is an inward force on the surface molecules causing the liquid to contract. Second is a tangential force parallel to the surface of the liquid. The net effect is the liquid behaves as if its surface were covered with a stretched elastic membrane.
Because of the relatively high attraction of water molecules to each other through a web of hydrogen bonds, water has a higher surface tension (72.8 milli newtons (mN) per meter at 20 °C) than most other liquids. Surface tension is an important factor in the phenomenon of capillarity.
Surface tension has the dimension of force per unit length, or of energy per unit area. The two are equivalent, but when referring to energy per unit of area, it is common to use the term surface energy, which is a more general term in the sense that it applies also to solids.
In materials science, surface tension is used for either surface stress or surface energy.
Formula for surface tension
Where, 
L=Length
F= force
S.I. Unit of Surface tension is N/m
The dimensional formula of surface tension is MT-2.
Capillarity:
It is the rise or depression of a liquid in a small passage such as a tube of small cross-sectional area, like the spaces between the fibres of a towel or the openings in a porous material.
Capillary action occurs when the adhesion to the walls is stronger than the cohesive forces between the liquid molecules. The height to which capillary action will take water in a uniform circular tube (picture to right) is limited by surface tension and, of course, gravity.
A tube of very fine bore is called capillary. The phenomenon of rise or fall of a liquid in a capillary tube is called capillarity.
If we consider meniscus to be hemispherical in shape, the weight of the liquid rise (the total upward force) = (Volume of liquid in cylinder upto h + volume of liquid in cylinder of radius r and height r – volume of hemisphere of radius r) ρg.
Figure 4: Capillarity phenomenon
2πr×Tcosθ=[πr2×h+πr2×r−23πr3]ρg2πr×Tcosθ=[πr2×h+πr2×r-23πr3]ρg
T=r(h+r3)ρg2cosθT=r(h+r3)ρg2cosθ.
For capillary r3r3 can be neglected h=2Tcosθrρgh= 2Tcosθrρg.
This is called Ascent formula.
Key Takeaways:
It is the rise or depression of a liquid in a small passage such as a tube of small cross-sectional area, like the spaces between the fibres of a towel or the openings in a porous material.
Vapour pressure is a measure of the tendency of a material to change into the gaseous or vapour state, and it increases with temperature. The temperature at which the vapour pressure at the surface of a liquid becomes equal to the pressure exerted by the surroundings is called the boiling point of the liquid.
P solution = X solvent P solvent
P solution | = | |
X solvent | = | |
Psolvent | = | vapor pressure of the pure solvent |
Key Takeaways:
Vapour pressure is a measure of the tendency of a material to change into the gaseous or vapour state, and it increases with temperature.
It is reciprocal of Bulk modulus (K)
ß=1/K
Bulk Modulus is defined as the ratio of compressive stress to volumetric strain.
K= 
-ve sign means the volume decrease with increase in pressure.
We know that, 
Since, R= Characteristics gas constant and T is constant (isothermal process).
Differentiating the above equation
Now the isothermal bulk modulus
KT=
.(dp/d
)= 
. RT=P
KT=P
The hydrostatic pressure is the pressure exerted by a fluid at equilibrium at any point of time due to the force of gravity. Hydrostatic pressure is proportional to the depth measured from the surface as the weight of the fluid increases when a downward force is exerted.
Fluids exert pressure in all directions equally. This rule leads to another interesting occurrence. If we consider the layer of water on the top of a bottle, the pressure exerted by the layer of water acts on the container at the sides, the surface of air on top and the layer of water at the bottom. As we move down from the top of the bottle to the bottom, the pressure exerted by the top layer on the bottom adds up.
Due to this phenomenon, the fluid at the bottom of the container experiences more pressure that the fluid which is above it.
Hydrostatic force refers to the total pressure acting on the layer or surface which is in touch with the liquid or water at rest. If the liquid is at rest then there is no tangential force, and hence the total pressure will act perpendicular to the surface with contact.
The location of total pressure is referred as the center of pressure which is always below the center of gravity of the surface in contact.
Forces on the curved surface:
For forces on the curved surface, there will be two forces required to determine the resultant hydrostatic force.
• Horizontal force
• Vertical force
Horizontal force on curved surface:
The vertical plane shall be considered to determine the horizontal force, which is the vertical projection of the curved surface generally rectangle. But in case of hemispherical or spherical, it becomes circular shape.
Express the horizontal component of force.
Vertical force on curved surface:
It is the weight of the liquid acting on the curved surface in contact with the liquid which may be in upward direction due to buoyancy or downward direction due to the weight of the fluid.
Express the vertical component of force.
Therefore, the resultant force on the curved surface is,
1.12.1 Manometers:
Manometer is a simple and inexpensive device of measuring pressure and pressure difference. It is usually bent to form a U-tube and filled with liquid of known specific gravity. The surface of the liquid will move in proportion to changes of pressure.
Types of Manometer:
Piezometer is the simplest form of manometer which is tapped into the wall of pressure conduit for the purpose of measuring pressure. Though effective in many purposes, piezometer is not practical to use in lighter liquids with large pressure and cannot be used to measure gas pressure.
Figure 5: Piezometer
From the figure above, three piezometers A, B, and C are attached to a pressure conduit at bottom, top, and side, respectively. The column of liquid at A, B, and C will rise at the same level above M indicating a positive pressure at M.
2. Open Manometer:
Open manometer is a tube bent into a U-shape to contain one or more fluids of different specific gravities. It is used to measure pressure. Example of open manometer is shown below.
Figure 6: Open Manometer
3. Differential Manometer:
Differential manometer cannot measure pressure but can measure pressure difference. Frequently in hydraulic problems, difference in pressure is more useful information than the pressure itself.
Figure 7: Differential Manometer
1.12.2. Buoyancy:
Buoyancy is the force that causes objects to float. It is the force exerted on an object that is partly or wholly immersed in a fluid. Buoyancy is caused by the differences in pressure acting on opposite sides of an object immersed in a static fluid. It is also known as the buoyant force.
Force of Buoyancy:
When we submerge an object in a fluid, an upward force is experienced by the object. This force is applied by the fluid on the objects which makes it to, rises up and is called the Force of Buoyancy. The scale of this force is precisely equal to the amount or weight of the liquid displaced.
According to the Archimedes’ Principle
Fb | = | buoyant force |
| = | |
g | = | |
V | = | fluid volume |
The unit of the buoyant force is the Newton (N).
Center of Buoyancy:
The point where the force of Buoyancy is applied or the point on the object where the force acts are termed as the Center of Buoyancy.
It should be illustrated that the force of buoyancy is a vertical force, and thus, the Center of Buoyancy is the point situated on the centre of the gravity of the liquid that is being displaced by the object submerged.
1.12.3. Uniformly Accelerated motion:
In general, a uniformly accelerated motion is the one in which the acceleration of the particle throughout the motion is uniform. It can be moved in one dimension, two dimensions, or three dimensions.
If an object's speed (velocity) is increasing at a constant rate then we say it has uniform acceleration. The rate of acceleration is constant. If a car speeds up then slows down then speeds up it doesn't have uniform acceleration.
Figure 8: uniform Acceleration motion
Key takeaways:
References:
