undefined | unit 5 electronic communication systems

Back to Study material

BEE

UNIT 5

Electronic Communication Systems

Q1. Explain about the element of communication system?

A1.

Information Source

It produces a message that is analog in nature, i.e., the output of the information source is a continuous signal.

Analog carrier source

Sine wave is used as a carrier signal which will help in analog modulation.

Analog modulation

The carrier signal is superimposed with the message signal and then the modulated signal is obtained which is also analog in nature.

Communication channel

The analog modulated signal is transmitted via the communication channel towards the receiver end after addition of the requisite power levels.

Analog demodulation

At the receiver end, the incoming modulated signal is passed through an analog demodulation process which extracts the analog message signal. The analog message is then passed onto the final destination.

Destination

The nature of signal starting from the information source till the final destination is analog.

Q2. What do you understand by IEEE frequency spectrum?

A2.

Q3. What is the function of Transmission media?

A3.

Receiver :-The received signal is processed by the various circuits like preamplifier, mixer, oscillator, detector, demodulator, driver amp and power amp.

In telephone baseband communication:-Analog information transmitted through parallel two wires.

The bandwidth of 300Hz to 3400Hz is adequate for a telephone voice conversation, 15Hz to 20Hz for music and 5Hz bandwidth for a typical video signal.

Transmission Media :-

1>. Guided:-Signals are transmitted via a physical and tangible guide betn the communicating points. These parallel wire, coaxial cable, wave guides and optical fibre.

2>. Unguided: - Physically there is no direct physical connection betn points such as microwave & satellite links. Mobile phone also uses unguided transmission media.

Q4. Explain the necessity of Modulation in detail.

A4. 1>. Antenna height reduces

2>. Avoids mixing of signal

3>. Increases the range of communication [ InKilometers]

4>. Multiplexing of signals is possible

5>. Improves quality of reception of signal.

1>. Antenna height Reduces :- Antenna theory specifies that the height of the antenna required for radiation of radio waves is a function of wavelength of the freqn fed at the i/p of the antenna. Antenna height must be multiple of ( d/4 ),

Where ‘ d ‘ is the wavelength.

d = speed of light / freqn of signal

d = c / f = 3 x 108 / f

eg : Consider the voice as analog baseband signal with f = 4 KHz

d = 3 x 108 / 4 x 103

d = 75 x 103 m

d = 75 km

Height of antenna required is d / 4

= 75 km / 4 = 18.75 km

Practically you cannot build the antenna of 18.7 km height. Consider this voice signal of 4 kHz freqn is used to modulate the carrier signal of 2 MHz freqn.

F = 2 MHz

D = c / f = 3 x 108 / 2 x 106 = 150 m

Minimum height of antenna required = d / 4 = 150 / 4 = 37.5 m

Therefore antenna height required for radio communication reduces from 75 km to 37.5 meters due to modulation.

3>. Increase range of communication :- The freqn of baseband signal is low. At low freqn the signal radiation from antenna is poor or weak. Due to this reason the signal gets attenuated and cant travel long distance when it is transmitted.

Attenuation of the transmitted signal reduces when the freqn is increased.

Thus modulation increases the freqn of the signal to be radiated. Thus increase in freqn increases the range of communication.

Q5.Write a note on various Modulation Techniques :-

A5. AM :-“ The process of changing the amplitude of the carrier wave as per the intensity [ amplitude ] of the modulating signal is called as Amplitude Modulation “.

$C:\Users\i7\Desktop\Image\2.jpg$

FM :- “ In freqn modulation the freqn of a carrier signal is varied by the modulating signal “.

“ The process of changing the freqn of the carrier wave according to the intensity [ amplitude ] of the modulating signal is called as freqn modulation “.

$C:\Users\i7\Desktop\Image\3.jpg$

Q6.Compare AM &FM.

A6.

Sr No	A.M.	F.M.
1>.	Amplitude of carrier is charged in accordance with amplitude of modulating signal.	Freqn of carrier is change in accordance with amplitude of modulating signal.
2>.	Freqn is constant	Amplitude is constant
3>.	The AM signal is given as, XAM (t) = Ac [ 1 + m x(t)] Cos (wct)	The FM signal is given as XFM (t) = Ac [ Cos (wct) + 2 ∏ Kf x(t)]
4>.	Modulation index of AM, M = Am / Ac	Modulation index of FM, Βf = Δf / fm, where Δf = Am Kf
5>.	BW = 2 fm. Bandwidth of AM is 2W where W is bandwidth of modulating signal & 2fm is for single tone modulation.	Bandwidth of FM is BT = 2 ( βf + 1 )W, where W is bandwidth of modulating signal. For single tone modulation BW = 2 ( Kf Am + fm )
6>.	Requires small bandwidth compared to FM.	Required large BW compared to AM.
7>.	It has only two sidebands for single tone modulation.	It has infinite sidebands even for single tone moduln.
8>.	It is not suitable for high quality music broadcasting.	It is suitable for high quality music broadcasting.
9>.	Noise immunity is low	It has better noise immunity than AM.
10>.	It is suitable for long distance transmission	It is suitable for line of sight transmission.
11>.	Used in MW, SW broadcasting, video transmission in T.V.	It is used in high quality music broadcasting audio broadcasting in T.V.
12>.	Cannot reject interfering signals in the same band.	Can reject interfering signals in the same band due to capture effect.
13>.	Transmission efficiency is poor due to use of Class A & amplifiers.	Transmission efficiency is better due to use of Class C ampr.

Q7.What is the main function of Mobile communication systems explain?

A7. Cellular telephone systems, also referred to as Personal Communication Systems (PCS), are extremely popular and lucrative worldwide: these systems have sparked much of the optimism about the future of wireless networks. Cellular telephone systems are designed to provide two-way voice communication at vehicle speeds with regional or national coverage. Cellular systems were initially designed for mobile terminals inside vehicles with antennas mounted on the vehicle roof. Today these systems have evolved to support lightweight handheld mobile terminals operating inside and outside buildings at both pedestrian and vehicle speeds.

Frequency reuse

It is process of combining analog and digital signal to send over shared medium.

It divides the capacity of communication channel into multiple channels

Multiplexing is divided into space division, frequency division and time division multiplexing.

Space Division Multiplexing

In wired medium, separate point to point conductors are used to each channel.

In wireless medium multiple elements of antennas are used such that it forms phased array antenna.

Multiple output, multiple input and single input multiple output are the examples of this.

Frequency Division Multiplexing

In this multiple signal are send in distinct frequency in single medium.

The signals are electrical.

Radio, television broadcasting are the examples of FDM.

The service provides can send several channels or signals continuously to all subscribers even the customer has single cable connection.

Time Division Multiplexing

In this for separation of data streams the time is used instead of frequency and space.

It consists of group of bits in sequence one after another.

Each sequence is associated with each receiver.

Carriers sense multiple access and multidrug are the eaxples of time division multiplexing.

Q8.Write a short note on Channel Assignment?

A8. It means assigning channels or spectrum bands to radio interfaces for communication.

There are two channel assignment strategies in cellular system.

A. Fixed channel assignment:

In fixed channel assignment each cell is permanently allocated predetermined group of channels. Any call attempt within cell can only be served by unused channels in that particular cell.

If all channels are occupied, the call is blocked and subscriber does not receive service.

Borrowing technique where a cell is allowed to borrow channels from a neighbouring cell if all channels are already occupied is always used with this type of strategy. Mobile Base station (MSC) monitors the function of base station including borrowing ensuring that borrowing does not interfere with any call in progress in donor cell.

B. Dynamic channel assignment:

In dynamic channel assignment strategy, voice channels are not allocated permanently.

Entire pool of frequency channels lies with MSC and each time a call request is made, the serving base station requests a channel from the MSC. Switch then allocates a channel to the requested cell following a algorithm.

MSC allocates frequency channels on dynamic basis if that frequency channel is not presently in use in the cell or any other cell which falls within the minimum restricted distance of frequency reuse to avoid co-channel interference.

It reduces chances of blocking which increases trunking capacity of system as all available channels are accessible to all cells.

In this MSC has to collect real time data on channel occupancy, traffic distribution, radio signal strength indication of all channels on continuous basis, thus increasing the computational load on MSC.

Q9. Explain about the work of Handoff strategies?

A9. Processing handoffs is an important task in any cellular radio system. Handoffs must be performed successfully and as infrequently as possible and be imperceptible to the user. In order to meet these requirements, system designer must specify an optimum signal at which to initiate a handoff.

This margin is given by cannot be too large or too small. If is large unnecessary handoffs which burden the MSC may occur and if is too small, there may be may be insufficient time to complete a handoff before a call is lost to meet these conflicting requirements. Figure is given which explains the different steps of handoff required to meet.

Following figure demonstrates the case where a handoff is not made and the signal drops below the minimum acceptable level to keep the channel active. This dropped call event can happen when there is an expansive delay by the MSC in assigning a handoff or when the threshold is set too small for the handoff time in the systems. Excessive delay may occur during high traffic conditions or due to no channels are available on any of the nearby base stations.

In deciding when to handoff, it is important to ensure that the drop in the measured signal is not due to momentary fading and the mobile is actually moving away from the serving base station. But when there is a drop in the measured signal level due to momentary fading and not due to the actual moving mobile away from the base station, that is situation if the handoff of a call takes place then such handoffs must be prevented by ensuring that the base station monitors the signal level for a certain period of time before the handoff is initiated.

Q10. What do you understand by Cell Splitting?

A10.

Cell splitting is the process of subdividing a congested cell in to smaller cells, each with its own base station and corresponding reduction in antenna height and transmitter power.

Cell splitting increases the capacity of a system since it increases number of times that channels are reused.

In cell splitting original cell is split in to smaller cells. New cell radius is half of the original radius.

In this the cell boundaries need to be revised so that the local area which was earlier considered as a single cell can now contain number of smaller cell ,these new cells are called microcells

Dynamic cell splitting: This technique is based on utilizing the allocated spectrum efficiency in real time. In this of splitting techniques cells are not splitted permanently depending on requirement of traffic the splitting of the cells are carried out.

The algorithm for dynamically splitting cell sites is a tedious job since we cannot afford to have single cell unused during cell splitting at heavy traffic hours. Proof:

When the cell radius is reduced by a factor, it is also desirable to reduce the transmitted power. The transmit power of the new cells with radius half that of the old cells can be found by examining the received power PR at the new and old cell boundaries and setting them equal.

This is necessary to maintain the same frequency re-use plan in the new cell layout as well. Assume that PT1 and PT2 are the transmit powers of the larger and smaller base stations respectively. Then, assuming a path loss index n=4, we have power received at old cell boundary = PT1/R4 and the power received at new cell boundary = PT2/(R/2)4. On equating the two received powers, we get PT2 = PT1 / 16. In other words, the transmit power must be reduced by 12 dB in order to maintain the same S/I with the new system lay-out.

At the beginning of this channel splitting process, there would be fewer channels in the smaller power groups.

As the demand increases, more and more channels need to be accommodated and hence the splitting process continues until all the larger cells have been replaced by the smaller cells, at which point splitting is complete within the region and the entire system is rescaled to have a smaller radius per cell.

If a cellular layout is replaced entirety by a new layout with a smaller cell radius, the signal-to-interference ratio will not change, provided the cluster size does not change. Some special care must be taken, however, to avoid co-channel interference when both large and small cell radii coexist.

It turns out that the only way to avoid interference between the large-cell and small-cell systems is to assign entirely different sets of channels to the two systems.

So, when two sizes of cells co-exist in a system, channels in the old cell must be broken down into two groups, one that corresponds to larger cell reuse requirements and the other which corresponds to the smaller cell reuse requirements.

The larger cell is usually dedicated to high speed users as in the umbrella cell approach so as to minimize the number of hand-offs.

Q11. Explain Gsm system with the help of Block diagram?

A11.

A GSM system consists of three subsystems:

1. Radio Sub System (RSS)

2. Network and Switching Subsystem (NSS)

3. Operation Sub System (OSS)

Radio Sub System

In GSM network all radio specific entities are comprised in radio sub systems. RSS consists the two main entities as:

(i) Mobile Station (MS)

(ii) Base Station System

The basic function of RSS is to connect the mobile station to the network. The RSS can consist a number of Base Station Controller (BSC) and each BSC connects to the number of Base Transceiver Systems (BTS) and each BTS connects to a number of mobile stations (MS).

(i) Mobile Station (MS)

A Mobile Station (MS) consists of several functional groups.

(a) Mobile Terminal (MT)

Mobile Terminal offers common functions used by all services. MT transmits through the interface Um.

(b) TA (Terminal Adapter)

Terminal adaptation hides the radio specific characteristics.

A user terminal through which the user receives and sends the data. It can be a headset, microphone etc.

(d) SIM (Subscriber Identity Module)

It is a card inserted into the MS. SIM uniquely identifies the user to the services, stores user parameters and enables the MS to connect to the GSM network.

(ii) Base Station Subsystem (BSS)

BSS have two main components :

(a) Base transceiver station

It connects to a number of mobile stations. The connection between the MS and BTS is established through the Um user interface. Main functions performed by BTS are as follows:

(i) Processing of signals

(ii) Formation of cells

(iii) Amplification of signals

(iv) Frequency hopping

(v) Channel coding and decoding

(vi) Encryption and decryption of data.

Fig.: MS and BTS connection through Um in GSM cell

(b) Base station controller

It manages a number of BTSS. It uses the Abis interface to connect to various BTSs main functions performed by BSC are as follows:

(i) Processing of signals

(ii) Switching between BTSs

(iii) Controlling BTSs

(iv) Reserving radio frequencies

(v) Frequency hopping and paging.

(vi) Authentication, encryption and decryption of data.

Q12. What is the function of Network and Switching Subsystem?

A12.

NSS can be considered as the heart of the GSM system. The NSS connects the wireless network with standard public network.

Switching, mobility management, interconnection to other network, system control are some main work of NSS.

The NSS consists of the following databases and switches:

(i) Mobile Services Switching Center (MSC)

There are mainly high-performance digital ISDN switches. They used to set up the connections to other MSCs and to the BSCs over the A interface.

The main aim of MSCs is to manage the various BSCs in a geographical region. The various functions performed by MSC are as follows:

(i) Establish the connections to other fined network, such as PSTN and ISDN via Gateway MSC (GMSC) or Interworking functions (IWF).

(ii) Handles all signaling needed for connection setup, connection release and handover of different connections to the other MSCs.

(iii) Call monitoring of MS.

(iv) Supplementary service support such as call forwarding multi-party calls.

(ii) Gateway Mobile Service Switching Centre (GMSC)

This is a MSC which handles connections to other networks like ISDN, PSTN, PSPDN.

(iii) Home Location Register (HLR)

HLR is important database in a GSM system that stores all relevant information of user. It stores the Mobile Subscriber ISDN (MSISDN) number, subscribed services such as call forwarding, roaming, GPRS, subscriber’s ISMI, user’s location Area, Users current VLR and MSC status.

A unique HLR record is maintained for each mobile user, which is updated on a real-time basis. HLR can manage data for huge number of customers with the help of highly specialized databases.

(iv) Visitor Location Register (VLR)

VLR is a dynamic database which associated to each MSC.

VLR is used to stores all important information needed for the mobile station users, such as the current location area (LA) information that is connected to MSC. If a new MS comes into other location area then VLR copies all relevant information of this user from HLR.

Operation Sub System (OSS)

OSS work for the operation and maintenance of the entire network. The main components of OSS are Operation and Maintenance Centre (OMC), Authentication Centre (AuC) and Equipment Identity Register (EIR).

(i) Operation and Maintenance Center (OMC)

The OMC monitors and controls all other network entities over the O interface.

Main functions of OMC are management of status reports of network entities, Subscriber security management, traffic monitoring and accounting and billing.

(ii) Authentication Centre (AuC)

AuC is used by the HLR to authenticate the user, AuC is used to protect user identity and data transmission.

The AuC used various algorithms for authentication as well as use the keys for encryption and generates the values needed for user authentication in HLR.

(iii) Equipment Identity Register (EIR)

EIR works as the database for all International Mobile Equipment identity (IMEI), it stores all device identifications registered for this network such as the mobile equipment manufacturer and model.

Stolen or malfunctioning mobile station can be locked by using the black list of EIR.

Sign Up