Unit – 2

Gear and Gear Trains

Q1) What is the Gear Terminology and definitions

A1) Gear can be defined as the toothed member that is used to transmit the power from one shaft to another shaft. Gear transmits the motion by direct contact. Among the two meshing gears smaller one is known as the pinion while larger one is known as wheel or gear. Gears are broadly classified on the basis of layout of connecting shaft.

Q2) What is the Gear Terminology 

A2) Gear Terminology

Gear terminology is the various terms to study the gear which is being discussed below and figure 1 show the various terms used in gear terminology.

Figure. Gear Terminology

Pitch Circle: It is an imaginary circle which transmits the same motion by pure rolling as the transmitted by the gears in mesh.

Pitch Circle Diameter: Diameter of pitch circle is known as the pitch circle diameter.

Circular pitch: Circular pitch is the distance of a point on one tooth to the corresponding point on the adjacent tooth along the pitch circle. It is denoted by the p.

t = number of teeth.

d = pitch circle diameter.

Diametral Pitch: Diametral pitch of a gear is the number of teeth per unit length of pitch circle diameter in inches. It is denoted by P.

Module: it is the ratio of pitch circle diameter in mm to the number of teeth on the gear. it is denoted by m.

Gear Ratio: Gear ratio is the ratio of number of teeth on driven gear to the number of teeth on driving gear. it is denoted by G.

T= number of teeth on driven gear.

t = number of teeth on driving gear.

Velocity ratio: It is the ratio of angular velocity of driven gear to the angular velocity of driving gear. It is denoted by VR.

Let N be the rpm,  be the angular velocity and T be the number of teeth on gear. while subscript 1 and 2 are used for the driving and driven gears respectively.

Addendum circle: It is the circle passing through the tip of the gear tooth.

Addendum: It is the height of the gear tooth in radial direction above the pitch circle. Standard value of addendum is one module.

Dedendum Circle: The circle passing through the root of circle is known as the dedendum circle.

Dedendum: It is the depth of gear tooth along the radial direction below the pitch circle. Its standard value is 1.157 modules.

Clearance: It is the difference between the addendum and dedendum of the gear. Standard value of clearance is 0.157m.

Full depth of teeth: It is the total radial depth of the gear tooth. It is calculated by adding the addendum and dedendum of the gear tooth.

Working depth of teeth: It the maximum depth up to which tooth of one gear penetrate in the mating gear. It is calculated by adding the addendum of the mating gears.

Space width: It is the width of space between the two adjacent teeth of a gear along the pitch circle.

Tooth thickness: It is the thickness of the gear tooth measured along the pitch circle.

Backlash: Backlash is defined as the difference between the tooth thickness and the space width.

Face width: It is the width of the gear tooth measured along the axis of gear.

Top land: Top surface of the gear tooth.

Bottom land: The bottom surface of the tooth between the adjacent fillets.

Face: It the surface of tooth between the pitch circle and top land.

Flank: It the surface of tooth between the pitch circle and the bottom land which also includes the fillet.

Line of action: It is the line joining the pitch point to the point of contact of two mating gear along which the driving gear exerts force on the driven gear. It is also known as the pressure line.

Pressure angle: It is the angle between the common tangent to the pitch circle and the line of action. It is also known as angle of obliquity and denoted by .

Path of contact: It is the locus of point of contact of two mating gears from beginning of contact up to disengagement of the gears. It constitutes of following two paths.

Path of approach: It is the locus of point of contact from starting of engagement to pitch point.

Path of recess: It is the locus of point of contact from pitch point to the end of engagement.

Arch of contact: It is the locus of point of contact along pitch circle form beginning of engagement to end of engagement. Just like path of contact it can also be divided in two parts.

Arc of Approach: It is the part of arc of contact from beginning of engagement to pitch point.

Arc of Recess: It is the part of arc of contact from pitch point to end of engagement.

Angle of action: It is the angle turned by the pair of teeth of gears from beginning of engagement to the end of engagement.

Contact ratio: It is the ration of arc of contact to the circular pitch  

Q3) Explain the Interference and Undercutting

A3) Locking of meshed gear teeth due non-conjugate or non-involute profile is termed as the interference. Non-conjugate gear teeth profile causes improper sliding of gear teeth which results in rough action and binding. Rough action and binding cause different sliding velocity of mating gears and results in locking.

Minimum number of teeth to avoid interference

Undercutting

In case of involute gear profile addendum of mating gears removes some part in the dedendum if there is interference. This removed portion in the dedendum is known as the undercut and the process of removal of the material from at the root of gears is known as undercutting. Figure 6 shows the undercutting in the gears

Q4) Define the Types Methods for eliminating Interference

A4) Minimum Number of Teeth on the Pinion in Order to Avoid Interference

Minimum Number of Teeth on the Wheel in Order to Avoid Interference

Minimum Number of Teeth on a Pinion for Involute Rack in Order to Avoid Interference.          

Q5) Explain the Minimum number of teeth to avoid interference.  

A5) We have already discussed in the previous article that in order to avoid interference, the addendum circles for the two mating gears must cut the common tangent to the base circles between the points of tangency. The limiting condition reaches, when the addendum circles of pinion and wheel pass through points N and M (see Fig. 12.13) respectively

t = Number of teeth on the pinion,

 T = Number of teeth on the wheel,

m = Module of the teeth, r = Pitch circle radius of pinion = m.t / 2

 G = Gear ratio = T / t = R / r

φ = Pressure angle or angle of obliquity

From triangle

Limiting radius of the pinion addendum circle

AP .m = Addendum of the pinion, where AP is a fraction by which the standard addendum of one module for the pinion should be multiplied in order to avoid interference.

 We know that the addendum of the pinion

This equation gives the minimum number of teeth required on the pinion in order to avoid interference.

Q6) Explain the Simple Gear Train

A6) Simple gear train

A simple gear train is the combination of gears in which only one gear is fixed on one shaft. in these gear trains two mating pairs rotate in opposite direction. If there are more than two gears in the gear train then even number gears rotate in one direction and odd number gears rotate in same direction but opposite to even number gears. Figure 7 shows the arrangement of gears in simple gear train.

Figure. Arrangement of gears in simple gear train

In the analysis of a gear train, we try to find out the train value which is defined as the ratio of speed of speed of driven gear to the speed of driving gear. The train value is used to calculate the angular velocity transmitted by the gear train.

For simple gear train shown in figure 7, N represents the angular velocity of each gear followed by its number in subscript, similarly T represents the number of teeth on each gear.

In case of gears in mesh 

By multiplying all the above equations

Q7) Explain the Epicyclic train and their applications

A7) Apart from rotation of gears if any gear axis is also rotating with respect to some other axis the gear train is termed as epicyclic gear train. To rotate the axis of gear a very important link is used which is known as arm or carrier which is not gear.

The epicyclic great train shown in figure 10 has gears S and P and the arm a. The gear S and P are in mesh are rotating about their own axis with the help on arm a, axis of both the gear are rotating with respect to axis of each other. The degree of freedom for the epicyclic gear train is 2.

Consider the number of teeth on S and P gears are Ts and Tp respectively. In order to analyze the epicyclic gear train shown in figure 10 let us assume clockwise rotation is taken as positive and counter clockwise rotation as negative and now follow the given steps and prepare the table 1 shown below.

3.     Now multiply the rpm of each component by x.

4.     At last, add the rpm of arm which is assumed to be y.

5.     Then put the rpm of each component equal to the condition given in question and solve the problem accordingly.

Table.1. Analysis table for epicyclic gear train

Now substitute the rpms of given component according the condition given in question and solve.

Q8) Explain the Design of Spur Gears

A8) Sometimes, the spur gears (i.e., driver and driven) are to be designed for the given velocity ratio and distance between the centres of their shafts. Let

x = Distance between the centres of two shafts,

N1 = Speed of the driver,

T1 = Number of teeth on the driver,

d1 = Pitch circle diameter of the driver

N2, T2 and d2 = Corresponding values for the driven or follower, and

 pc = Circular pitch.

 We know that the distance between the centres of two shafts,

and speed ratio or velocity ratio,

From the above equations, we can conveniently find out the values of d1 and d2 (or T1 and T2) and the circular pitch (pc). The values of T1 and T2, as obtained above, may or may not be whole numbers. But in a gear since the number of its teeth is always a whole number, therefore a slight alteration must be made in the values of x, d1 and d2, so that the number of teeth in the two gears may be a complete number.                         

Q9) In an epicyclic gear train, the internal wheels A and B and compound wheels C and D rotate independently about axis O. The wheels E and F rotate on pins fixed to the arm G. E gears with A and C and F gears with B and D. All the wheels have the same module and the number of teeth is: TC = 28; TD = 26; TE = TF = 18. 1. Sketch the arrangement; 2. Find the number of teeth on A and B.

A9) Given: TC = 28; TD = 26; TE = TF = 18

The arrangement is shown in Fig. 13.12. 2.

Number of teeth on wheels A and B Let

TA = Number of teeth on wheel A, and

 TB = Number of teeth on wheel B.

If dA, dB, dC, dD, dE and dF are the pitch circle diameters of wheels A, B, C, D, E and F respectively, then from the geometry of Fig,

dA = dC + 2 dE and

dB = dD + 2 dF

 Since the number of teeth are proportional to their pitch circle diameters, for the same module, therefore

TA = TC + 2 TE = 28 + 2 × 18 = 64

TB = TD + 2 TF = 26 + 2 × 18 = 62