Unit 3 | unit 3 timing circuits and oscillators 2

Back to Study material

Basic Electronics Engineering

Unit - 3

Timing Circuits and Oscillators

Q1) What do you understand by RC-timing circuits?

A1)

Time Constant: T = R C

Capacitors can be used, with a resistor, for timing.
The 555 timer relies on this.

The time constant calculations below are needed for designing timing circuits.

T is the time in seconds.
R is the resistor value in Ohms.
C is the capacitor value in Farads.

Here is a timing circuit. Click the switch the start charging or discharging

Fig: RC timing Circuit

Q2) Explain the IC 555 work and its application?

A2)

Some of the important features of the 555 timer are

The 555 timer can be operated at a wide range of power supplies ranging from 5 V to 18 V.
It is available in 3 different packages: 8-pin Metal Can package, 8-pin DIP and 14-pin DIP.
Timing can be anywhere from microseconds to hours.
It can operate in both astable and monostable modes.
High output current.
It has an adjustable duty cycle.
It is TTL compatible due to its high output current.
The output can source or sink a current of 200mA to the load.
It has a temperature stability of 0.005% per 0C.

Different Modes Of Operation

Generally, the 555 timer can be operated in three modes: Astable, Monostable (or one-shot) and Bistable.

Astable Mode

In this mode, the 555 work as a free running mode. The output of astablemultivibrator will continuously toggle between low and high, there by generating a train of pulse, which is why it is known as pulse generator.

It is a best example for a perfect square wave generator. They are used as an inverter and also used in many of the internal part of the radio. Selecting a Thermistor as a timing resistor allows the use of the 555 in a temperature sensor.

Monostable Mode

In the monostable mode, as the name suggests, it stays in its stable state until and unless an external trigger is applied. In this mode, the 555 functions as a “one-shot” pulse generator. The best application of a monostable is to introduce a time delay in to a system.

Applications comprise many things viz., timers, missing pulse detection also included bounce free switches, touch switches as well as frequency divider, capacitance measurement and pulse-width modulation (PWM) and many more.

Q3) Write a short note on Positive feedback?

A3)

I 1.png
An oscillator is a device that generates AC output signals without any input AC signal. A fraction of output is feedback to the input.

A= Gain of amplifier (open 100Þ)

Β= Feedback gain

V= input signal

Av= Amplified signal at output

A fraction of the signal βAv is feedback to the input. It must be ensured by the feedback circuit that feedback signal βAv must be in phase with input signal v.

Now C is connected to A and input signal is removed. The only signal which is to drive the amplifier is feedback (βAv)

Case (1)- If βA<1, βAv>V and the output signal will die out (damped oscillation)

Case (2)- If βA>1, βAv>V and the output signal will built up (growing oscillations)

I 4.png
Case(3)- If βA=1, no change occurs in the output and we get an output with constant magnitude (undamped or Sustained oscillations)

Thus to obtain Sustained oscillations, the loop gain βA of a positive feedback amplifier must be unity(1).

Derivation of overall gain of positive feedback amplifier

V= Vin + βVout

Vout = Av1

Vout = A(Vin+βVout )

Vout (1-Aβ)=AVin

AF=

Where AF is the gain with feedback

Q4) Explain the principle of Barkhausen's criteria for oscillation?

A4)

Barkhausen Condition – Condition that are required to be satisfied to operate the circuit as an oscillator are called as Barkhausen condition.

In oscillator circuit there is no input signal hence the feedback signal it say should be sufficient to maintain the oscillations.

Barkhausen condition states that

The loop gain (Aβ) is equal to unity i.e. =1
The phase shift around the loop is zero or an inteqer multiple of 2, i.e. <βA = 2n

Where n=0,1,2,……..

Types of Oscillator- An oscillator circuit is usually made up of transistor. A transistor can work as an oscillator to produce undamped continuous oscillations of any desired frequency it oscillatory and feedback circuits are properly connected to it. The oscillators differ only in the way of feedback to supply losses to the oscillatory circuit. The following are the important oscillators-

Weinbridge Oscillator
RC phase shift oscillator
Hartley Oscillator
Capitals Oscillator

Q5) Give a brief description on Wein bridge oscillator?

A5)

I 6.png
Wein Bridge Oscillator- In this, phase shift is produced by using 2 transistors. Each produces a phase shift of 180° and hence phase shift of 360° is obtained

It is a 2 stage amplifier with R-C bridge circuit. The bridge circuit has 4 arms each containing components R1C1 in Series, R2 C2 in parallel, R3 and R4. Q1 acts as an oscillator and amplifier where as Q2 Serves as an inverter

When circuit is closed through switch S, the bridge circuit produces the oscillations of frequency whose expression is given by-

If R1=R2=R and C1= C2 = C then

F =

A total phase shift of 360° is obtained at the output of the second transistor. A fraction of this output energy is fed back to the oscillatory circuit (bridge) at the upper terminal. This positive feedback is to meet with the losses in the oscillator and hence undamped oscillations are produced.

Advantages-

It has better stability
Output is constant
Overall gain is high
Frequency can be adjusted by varying C1 and C2

Disadvantages-

Costly
Cannot generate frequency>1MHz.

Q6) In the RC network of a Weinbridge oscillator R1 = R2 = 200kΩ, determine the value of each of the capacitor to obtain a frequency of 5kHz.

A6)

F =

F = 5kHz, = 5000Hz

R1= R2= 200kΩ = 200×103Ω

5000 =

C = = 159.15 pF

Expression for feedback factor (β) and frequency (f)

In order to obtain expression for β and f, we will consider only frequency sensitive arms AD and CD as shown in figure below

Vin is actually the output voltage V0which comes from the amplifier output and voltage across R2C2acts as a feedback voltage VF

Feedback factor β=

Let impedance of arm AD be Z1 and that of DC be Z2

Therefore VF = ×Vin{ using voltage divider}

β = = ………….(1)

Z1= R1 + = …………..(2)

Z2 = R2 || Xc2= = ………….(3)

Substituting equation (2) and (3) in (1)

β =

Substituting jw = S

β =

Resubstitute jw = S , S2 = j2 w2 = -w2

β =

Rationalize the above equation

β = ……………(4)

The phase shift introduced by the wien bridge circuit at the desired output frequency should be 0°. For that the imaginary part of equation (4) should have a zero value.

WC1R2(1-w2R1R2C1C2) = 0

w2R1R2C1C2 = 1

W =

F =

The above equation is the expression for the oscillator frequency.

If we substitute R1 = R2 = R and C1 = C2 = C

F = or w =

For β, if R1 = R2 = R, C1= C2 = C

β =

Substituting

W =

β = = =

Thus at the oscillator frequency F, the value of feedback factor β is

Q7) Explain the work faction of RC phase Shift Oscillator?

A7)

A typical RC phase shift oscillator using transistor as an active device is shown below

The output V0of the single stage CE amplifier has been connected as an input to the RC phase shift network. The output of the phase shift network is connected at the input of the amplifier.

As the amplifier is CE type it introduces phase shift of 180°. The phase shift network will introduce an additional 180° phase shift

Resistance R3 + Zi = R

Where Ziis input impedance of CE amplifier

Zi = hie || (R1 || R2)

Therefore R1 and R2 are large, we can neglect them

Therefore Zi = hie

So R3 = R- hie

Frequency of Oscillations is given by

F = * where k =