Unit - 5

Electrical Discharge Machining

Q1) Explain the working of EDM.

A)

Electrical discharge machining (EDM), sometimes also referred to as spark machining, spark eroding, burning, die sinking, wire burning or wire erosion, is a manufacturing process whereby a desired shape is obtained using electrical discharges (sparks).

Material is removed from the work piece by a series of rapidly recurring current discharges between two electrodes, separated by a die-electric liquid and subject to an electric voltage. One of the electrodes is called the tool-electrode, or simply the "tool" or "electrode", while the other is called the workpiece- electrode, or "workpiece".

Working of EDM:

Fig. Electrical discharge machining

• The diagram of electro discharge machining shown in figure.
• EDM is thermal erosion process whereby material is melted and vaporized from an electrically conductive work piece immerse in a liquid dielectric with a series of spark discharge between the tool electrode and the work piece created by a power supply.
• The electrode and the work piece are separated by a dielectric medium.
• The dielectric medium is like as kerosene, paraffin or light oil.
• The strong electrostatic field between the electrode and work piece produce emission of electrons from the cathode.
• In this gap between tool and work piece get ionized. The liquid is force to sparking zone.
• Due to high temperature, the metal at the sparking zone melts instantaneously.
• The material of the tool is usually a material which conduct electricity and which can be easily shaped.

Advantages: -

• Smaller holes can be easy machined.
• No contact between tool and work piece then tool life is increase.
• Any complex shape can be machined.

Disadvantages: -

• Tool life is no longer.
• Power consumption is high.

Q2) Describe surface finish and defined their factors.

A2) Surface finish:

The outermost boundary of a body adjacent to the air is called surface. When this surface deformed by a sharp cutting edge, the term surface finish describes the boundary.

A good surface is affected by many variables in single or multiple point machining.

Surface finish is defined in terms of 4 factors:

• Roughness – closely spaced surface irregularities, resulting from the manufacturing process or tools.
• Lay – the overall direction of the roughness pattern which can be affected by the machine and setup.
• Waviness – longer spaced irregularities caused by machine vibration and material warping among other factors.
• Flaws – unique surface imperfections in the material or processing.

Q3) Describe wire EDM in short.

A3)

• This process is similar to contour cutting with a band saw.
• A slow-moving wire travels along a prescribed path, cutting the work piece with discharge sparks.
• Wire should have sufficient tensile strength and fracture toughness.
• Wire is made of brass, copper or tungsten. (About 0.25mm in diameter).

Fig. Wire EDM

Q4) Define ECM and explain its working.

A4)

• Electrochemical Machining (ECM) is one of the newest and most useful non-traditional machining (NTM) process belonging to Electrochemical category.
• Electrochemical machining (ECM) is used to remove metal and alloys which are difficult or impossible to machine by mechanical machining process.
• The reverse of electroplating.
• This machining process is based Michael Faraday’s classical laws of electrolysis, requiring basically two electrodes, an electrolyte, a gap and a source of D.C power of sufficient capacity.

Working of ECM:

• In the actual process of ECM, the cathode is tool shaped (mirror image of work-piece) and anode is the work-piece.
• A gap (0.05 to 0.7 mm) is provided between the tool and work-piece and electrolyte flows through the gap at a velocity of 30 to 60 m/s and it completes the electrical circuit.
• Electrolyte is pumped at high pressure of 20 kgf/ (1.96 MPa) through the gap.
• Electrolyte must be circulated at a rate sufficiently high to conduct current between them and to carry heat.
• Metal is removed from the work-piece by dissolution
• The electric current is of the order of 50 to 40,000 A at 5 to 35 V D.C for current density of 20 to 300 A/.
• Power of 3 KWh is needed to remove 16 of metal which is almost 30 times the energy required in the conventional process (when the material is readily machinable).

Fig. Electro-chemical machining

Advantages of ECM:

• Process leaves a burr free surface.
• Does not cause any thermal damage to the parts.
• Lack of tool force prevents distortion of parts.
• Capable of machining complex parts and hard materials.
• ECM systems are now available as Numerically Controlled machining centers with capability for high production, high flexibility and high tolerances.

Q5) Explain MRR.

A5)

Material removal rate (MRR):

• Material removal rate (MRR) is an important characteristic to evaluate efficiency of a non-traditional machining process.
• In ECM, material removal takes place due to atomic dissolution of work material which is governed by Faraday’s laws of Electrolysis.

MRR = m / tρ = IA / Fρν

Where m = ItA/Fv = mass of material dissolve

I = current

A = Atomic weight

v = valency

F = Faraday’s constant = 96500 coulombs

ρ = density of the material

Power Supply:

1. Type: direct current

2. Voltage: 2 to 35 V

3. Current: 50 to 40,000 A

4. Current density: 20 A/cm2 to 300 A/cm2

Q6) What are the main components in EDM?

A6)

The main components in EDM:

• Electric power supply
• Dielectric medium
• Work piece & tool
• Servo control unit.
• The work piece and tool are electrically connected to a DC power supply.
• The current density in the discharge of the channel is of the order of 10000 A/cm2 and power density is nearly 500 MW/cm2.
• A gap, known as SPARK GAP in the range, from 0.005 mm to 0.05 mm is maintained between the work piece and the tool.
• Dielectric slurry is forced through this gap at a pressure of 2 kgf/cm2 or lesser.

Q7) Explain Power & Control Circuits in EDM.

A7)

Power & Control Circuits:

Two broad categories of generators (power supplies) are in use on EDM.  Commercially available: RC circuits based and transistor-controlled pulses.

In the first category, the main parameters to choose from a setup time are the resistance(s) of the resistor(s) and the capacitance(s) of the capacitor(s).

In an ideal condition, these quantities would affect the maximum current delivered in a discharge.

Current delivery in a discharge is associated with the charge accumulated on the capacitors at a certain moment.

Little control is expected over the time of discharge, which is likely to depend on the actual spark-gap conditions.

Advantage: RC circuit generator can allow the use of short discharge time more easily than the pulse-controlled generator.

Also, the open circuit voltage (i.e., voltage between electrodes when dielectric is not broken) can be identified as steady state voltage of the RC circuit.

In generators based on transistor control, the user is usually able to deliver a train of voltage pulses to the electrodes.

Each pulse can be controlled in shape, for instance, quasi-rectangular.

In particular, the time between two consecutive pulses and the duration of each pulse can be set.

The amplitude of each pulse constitutes the open circuit voltage.

Thus, maximum duration of discharge is equal to duration of a voltage pulse.  Maximum current during a discharge that the generator delivers can also be controlled.

Details of generators and control systems on EDMs are not always easily available to their user.

This is a barrier to describing the technological parameters of EDM process.  Moreover, the parameters affecting the phenomena occurring between tool and electrode are also related to the motion controller of the electrodes.

A framework to define and measure the electrical parameters during an EDM operation directly on inter-electrode volume with an oscilloscope external to the machine has been recently proposed by Ferri et al.

This would enable the user to estimate directly the electrical parameter that affect their operations without relying upon machine manufacturer's claims.

When machining different materials in the same setup conditions, the actual electrical parameters are significantly different.

When using RC generators, the voltage pulses, shown in Fig. Are responsible for material removal.

Fig. Voltage and current waveform during EDM

Q8) Write Advantages of ECM.

A8)

Advantages of ECM:

• Process leaves a burr free surface.
• Does not cause any thermal damage to the parts.
• Lack of tool force prevents distortion of parts.
• Capable of machining complex parts and hard materials.
• ECM systems are now available as Numerically Controlled machining centers with capability for high production, high flexibility and high tolerances.

Q9) Explain surface finish and tool wear.

A9)

Surface finish:

The outermost boundary of a body adjacent to the air is called surface. When this surface deformed by a sharp cutting edge, the term surface finish describes the boundary.

A good surface is affected by many variables in single or multiple point machining.

Surface finish is defined in terms of 4 factors:

• Roughness – closely spaced surface irregularities, resulting from the manufacturing process or tools.
• Lay – the overall direction of the roughness pattern which can be affected by the machine and setup.
• Waviness – longer spaced irregularities caused by machine vibration and material warping among other factors.
• Flaws – unique surface imperfections in the material or processing.

Tool wear:

Tool subjected to:

1. Forces

2. Temperature

3. Sliding action

• After continuous use for some time, tool gives unsatisfactory or inefficient performance.
• Unsatisfactory or inefficient performance is due to “Tool Wear or Tool failure”. Consequences:

1. Loss of dimensional accuracy

2. Increased surface roughness

3. Increased power requirement

4. Excessive vibration and abnormal sound (Chatter)

5. Total breakage of the tool

Tool is replaced or reconditioned usually by grinding.

Tool Wear depending factors:

1. Type of tool material and its hardness

2. Type and condition of work piece material

3. Dimensions of cut (Feed and depth of cut)

4. Cutting speed

5. Tool geometry

6. Tool temperature (function of cutting speed, feed and depth of cut)

7. Type of cutting fluid

Classification of Tool Wear

1. Flank wear

2. Crater wear on tool face

3. Localized wear such as the rounding of Cutting edge

4. Chipping of the cutting edge

Q10) Explain the working of the Laser-beam machining.

A10)

Laser-beam machining is a thermal material- removal process that utilizes a high-energy, coherent light beam to melt and vaporize particles on the surface of metallic and non- metallic work pieces.

Lasers can be used to cut, drill, weld and mark. LBM is particularly suitable for making accurately placed holes.

Principle of Laser beam machining (LBM):

• Conversion of electrical energy into heat energy to emit laser beam energy.
• Laser beam is focused on lance then create high energy the high energy concentration on work piece then work piece is melt and vaporized of metal.

Working of LBM

Fig. Laser Beam Machining

• The diagram of LBM is shown in figure.
• Laser is stand for Light Amplification by Simulated Emulsion of Radiation.
• The work piece is placed on the aluminum work table which material is hard not cut by laser beam.
• Ruby rod is used into form of cylindrical crystal both ends of ruby rod are finished to optical tolerance.
• The flash lamp wound around the ruby rod and connected to power supply.
• The ruby rod becomes highly efficient on low temperature and low efficient on high temperature. It is thus continuous cooled with water, air or liquid nitrogen.
• When the light beam has been amplified sufficiently and intensity beam of light comes out form partially reflected end it is focused on the work piece at the focused very high temperature which vaporized and removes the metal on work piece.

Applications: -

• LBM can make very accurate holes as small as 0.005 mm in refractory metals ceramics, and composite material without warping the work pieces.
• It is used for welding of thin metal sheet.
• Leaser can be used for cutting as well as drilling.
• Heat treatment.
• It is used for cutting complex profile.

Q11) Explain the Plasma Arc Machining process.

A11)

Plasma Arc Machining is used to remove material from the workpiece. In this process, a high velocity jet of high-temperature gas is used to melt and remove material from the workpiece. This high velocity of hot gas is also known as plasma jet.

When a gas or air is heated at a temperature of more than 5000 °C, then it will start getting ionized into positive ions, negative ions and neutral ions. When the gas or air is ionized its temperature reaches from 11000 °C to 28000 °C and this ionized gas is called plasma.

The gas or air is heated with arc and the plasma produced by heating gas is used to remove material from the workpiece. So, the whole process is called Plasma Arc Machining.

Fig. Plasma Arc Machining

• In this case, the high velocity electrons of are collide with the gas molecules & metal to form ionization of beam.
• The plasma gas is forced through nozzle duct & is made to direct on the work piece to be machined.
• Much of the heating takes place in duct at about 1600 degree Celsius & metal removal is due to electron bombardment & hot plasma.

Mechanism of Metal Removal:

• The metal removal in PAM is due to high temperature of gases.
• The heating of work piece is due to direct electron bombardment plus convective heating of hot plasma.
• The heat produced is sufficient to raise the temperature above its melting point.  Approximately 45% of electrical power delivered to torch is used for removal metal from work piece.
• PAM is used for cutting, spraying, & surfacing operations.

Advantages of Plasma arc Machining:

1. Rapid Cutting Speeds:

• Plasma arc cutting is faster than oxyfuel for cutting steel up to 50 mm thick and is competitive for greater thickness.
• Plasma cutting achieves speeds greater than those of laser cutting systems for thickness over 3 mm.
• The fast-cutting speeds result in increased production, enabling systems to pay for themselves in as little as 6 months for smaller units.

2.     Wide Range of Materials and Thickness:

• Plasma cutting systems can yield quality cuts on both ferrous and nonferrous metals. Thickness from gauge to 80 mm can be cut effectively.

3.     Easy to Use:

• Plasma cutting requires only minimal operator training. The torch is easy to operate, and new operators can make excellent cuts almost immediately. Plasma cutting systems are rugged, are well suitable for production environments, and do not require the potentially complicated adjustments associated with laser cutting systems.

4.     Economical:

• Plasma cutting is more economical than oxyfuel for thickness under 25 mm, and comparable up to about 50 mm. For example, for 12 mm steel, plasma cutting costs are about half those of oxyfuel.

Disadvantages of Plasma Arc Machining:

• The cutter's electrode and nozzle sometimes require frequent replacement which adds to the cost of operation.
• Non-conductive materials such as wood or plastic cannot be cut with plasma cutters with transferred arc type.
• Another minor drawback is that the plasma arc typically leaves a 4–6-degree bevel on the cut edge, although this angle is almost invisible on thinner material, it is noticeable on thicker pieces.

Q12) Explain Electron Beam Machining.

A12)

• Electron Beam Machining (EBM) is a thermal process. Here a steam of high-speed electrons impinges on the work surface so that the kinetic energy of electrons is transferred to work producing intense heating.
• Depending upon the intensity of heating the work piece can melt and vaporize.
• The process of heating by electron beam is used for annealing, welding or metal removal.
• During EBM process very high velocities can be obtained by using enough voltage of 1,50,000 V can produce velocity of 228,478 km/sec and it is focused on 10 – 200 μM diameter.
• Power density can go up to 6500 billion W/sq.mm. Such a power density can vaporize any substance immediately.
• Complex contours can be easily machined by maneuvering the electron beam using magnetic deflection coils
• To avoid a collision of the accelerating electrons with the air molecules, the process has to be conducted in vacuum. So, EBM is not suitable for large work pieces. 
• Process is accomplished with vacuum so no possibility of contamination.
• No effects on work piece because about 25- 50μm away from machining spot remains at room temperature and so no effects of high temperature on work

Working of EBM

Fig. Electron Beam Machining

• The EBM beam is operated in pulse mode.
• This is achieved by appropriately biasing the biased grid located just after the cathode.
• Switching pulses are given to the bias grid so as to achieve pulse duration of as low as 50 μs to as long as 15 ms.
• Beam current is directly related to the number of electrons emitted by the cathode or available in the beam.
• Beam current once again can be as low as 200μ amp to 1 amp. Increasing the beam current directly increases the energy per pulse.
• Similarly increase in pulse duration also enhances energy per pulse.
• High-energy pulses (in excess of 100 J/pulse) can machine larger holes on thicker plates.
• A higher energy density, i.e., for a lower spot size, the material removal would be faster though the size of the hole would be smaller.
• The plane of focusing would be on the surface of the work piece or just below the surface of the work piece.

Applications: -

• Used for producing very small size holes like holes in diesel injection nozzles, Air brakes etc.
• Used only for circular holes.

Limitations: -

• Material removal rate is very low compared to other convectional machining processes.
• Maintaining perfect vacuum is very difficult.
• The machining process can’t be seen by operator.
• Work piece material should be electrically conducting.

Advantages: -

• Very small size holes can be produced.
• Surface finish produced is good.
• Highly reactive metals like Al and Mg can be machined very easily.

Q13) Write Advantages and Limitations of Electron Beam Machining.

A13)

Limitations: -

• Material removal rate is very low compared to other convectional machining processes.
• Maintaining perfect vacuum is very difficult.
• The machining process can’t be seen by operator.
• Work piece material should be electrically conducting.

Advantages: -

• Very small size holes can be produced.
• Surface finish produced is good.
• Highly reactive metals like Al and Mg can be machined very easily.

Q14) Write Advantages and Limitations of Laser Beam Machining.

A14)

Limitations: -

• Uneconomic on high volumes compared to stamping.
• Limitations on thickness due to taper.
• High capital cost.
• High maintenance cost.
• Assist or cover gas required

Advantages: -

• Very hard and abrasive material can be cut.
• Sticky materials are also can be cut by this process.
• It is a cost effective and flexible process.
• High accuracy parts can be machined.
• No cutting lubricants required.
• No tool wears.
• Narrow heat effected zone.
• No contact between tool and work piece.

Q15) Write Advantages of Plasma arc Machining.

A15)

Advantages of Plasma arc Machining:

5.     Rapid Cutting Speeds:

• Plasma arc cutting is faster than oxyfuel for cutting steel up to 50 mm thick and is competitive for greater thickness.
• Plasma cutting achieves speeds greater than those of laser cutting systems for thickness over 3 mm.
• The fast-cutting speeds result in increased production, enabling systems to pay for themselves in as little as 6 months for smaller units.

6.     Wide Range of Materials and Thickness:

• Plasma cutting systems can yield quality cuts on both ferrous and nonferrous metals. Thickness from gauge to 80 mm can be cut effectively.

7.     Easy to Use:

• Plasma cutting requires only minimal operator training. The torch is easy to operate, and new operators can make excellent cuts almost immediately. Plasma cutting systems are rugged, are well suitable for production environments, and do not require the potentially complicated adjustments associated with laser cutting systems.

8.     Economical:

• Plasma cutting is more economical than oxyfuel for thickness under 25 mm, and comparable up to about 50 mm. For example, for 12 mm steel, plasma cutting costs are about half those of oxyfuel.

Q16) Write Disadvantages of Plasma arc Machining.

A16) Disadvantages of Plasma Arc Machining:

• The cutter's electrode and nozzle sometimes require frequent replacement which adds to the cost of operation.
• Non-conductive materials such as wood or plastic cannot be cut with plasma cutters with transferred arc type.
• Another minor drawback is that the plasma arc typically leaves a 4–6-degree bevel on the cut edge, although this angle is almost invisible on thinner material, it is noticeable on thicker pieces.