UNIT 6 | unit 6 power transmission systems

BME

UNIT 6

POWER TRANSMISSION QUESTION

Question 1) What are the parameters we should consider in gear selection process?

Answer 1) Gear Selection Considerations

Gears are employed in a variety of mechanical devices, and, consequently, several different types and designs are available. The suitability of each type of gear and its exact design for a motion or power transmission application is dependent on the specifications and requirements of the application. Some of the principal factors which may be considered when designing and choosing a gear include:

1) Operational and environmental conditions

2) Dimensional restrictions

3) Transmission requirements

4) Design standards

5) Costs

Question 2) Explain the difference between open belts drive and crossed belt drive?

Answer 2) Differences between open belt drive and crossed belt drive

Open Belt Drive	Crossed Belt Drive
In open belt drive, belt proceeds from top of one pulley to the top of other pulley without crossing.	In crossed belt drive, belt proceeds from top of one pulley to the bottom of other pulley and thus crosses itself.
In open belt drive, driving shaft and driven shaft rotate in same direction.	In crossed belt drive, driving shaft and driven shaft rotate in opposite direction.
Contact angle (or wrap angle) between the belt and pulley is comparatively small (always below 180º in smaller pulley).	Contact angle between the belt and pulley is comparatively large (always above 180º in smaller pulley).
Length of the open belt is smaller as compared to cross belt.	For the same pulley diameter and same centre distance between driver and driven shafts, longer belt is required in cross belt drive.
Here belt remains in same plane in every rotation during its operation.	Here belt bends in two different planes in every rotation during its operation.
Here belt does not rub with itself. So belt life is considerably high.	Here belt rubs with itself and thus life of the belt reduces.
Open belt drive is suitable when driving and driven shafts are in horizontal or little bit inclined.	Cross belt drive can be advantageously applied for horizontal, inclined and vertical positions of driving and driven shafts.
Power transmission capacity is small due to smaller wrap angle.	It can transmit more power as wrap angle is more.

Question 3) Explain Creep in Belts?

Answer 3)

Consider as an open belt drive rotating in the clockwise direction. The portion of the belt leaving the driven and entering the driver is known as the tight side and a portion of the belt leaving the driver and entering the is known as the slack side. During rotation, there is an expansion of a belt on a tight side and contraction of the belt on the slack side.

Due to this uneven expansion and contraction of the belt over the pulleys, there will be a relative movement (motion) of the belt over the pulleys this phenomenon is known as Creep in a belt.

Question 4) Explain Slip in Belts?

Answer 4) Consider an open belt drive rotating in a clockwise direction, this rotating of the belt over the pulleys is assumed to be due to firm frictional grip between the belt and the pulleys.

When this frictional grip becomes insufficient, there is a possibility of forwarding motion of driver without pulley with it, this is known as the slip in a belt.

slip-of-belt

Therefore slip may be defined as the relative motion between the pulley and the belt in it. This reduces the velocity ratio and usually expressed in % and it is denoted by S.

Belt slip is caused due to the following reasons:

(a) Continuous run of the belt, pulley rim surface becomes very smooth,

(b) Decrease in the coefficient of friction in between the two surfaces.

(d) Large difference in the tension of the tight side (T1) and the slack side (T2).

Question 5) Explain the difference between belt drive and chain drive?

Answer 5) Belt Drive vs Chain Drive:

Belt Drive	Chain Drive
1) Belt drive is used for transferring the power.		The chain drive is also used for transferring power.
2) The belt drive is powered by only a belt.		The chain drive is powered by a chain loop.
3) Belt drives are made up of synthetic material. This is not stronger as compared to the belt drive.		Chain drives are made up of metal which is stronger and more durable.
4) Belt drives are used in mills.		The chain drive is used in bicycles, motorcycles, and many more engines.
5) In belt drive, little difficulties have when it gets damaged.		It is easier to change or fix when its get damage
6) Low or medium in price		Price is high
7) The belt drive is not the lubricating system		The chain drive is a lubricating system.
8) The belt drive is quieter than the chain drive.		The chain drive is not quittered than a belt drive.

Question 6) What are the different types of chains?

Answer 6)

In the field of Mechanical Engineering chains can be classified into three broad categories and those are:

Hoisting Chains
-Oval Link Chains
-Stud-Link Chains
2. Conveyor Chains
3. Power transmission Chain
-Block Chain
-Roller Chain
-Silent Chain or Inverted Tooth Chain

Question 7)Write applications of chain drives?

Answer 7)

Applications of chain drives

 They are used for power transmission

 They are used in transportation industry

 They are used in wood working machinery

 They are used in agricultural machinery

 They are used in oil well drilling rigs

 They are used in building construction

 They are used in material handling equipment

 They are used for lifting load

 They are used for carrying materials

Question 8) what are the different materials used to manufacture the gears?

Answer 8) Materials used to manufacture gears:

Tempered steel is one of the most common materials for different types of gears, and aluminium is also common. Other materials used are:

High strength steels
Forged stainless steels
Copper-based alloys
Cast or forged aluminium alloys
Cast iron or grey cast iron
Magnesium alloys

Question 9) what are the applications and utilities of gears?

Answer 9) Applications & Utilities of Gears

The different types of gears are present in many sectors, such as:

The agricultural sector, in which they play a key role in carrying out mechanized tasks, such as sowing, ploughing or irrigation, as well as in the tractors themselves.
In the automotive field, their function is usually to act as transmitters of forces and to regulate speed.
As for naval vehicles, gears operate on fishing boats, submarines, workboats or yachts.
In the generation of wind power, gears increase the speed of generators, a function that is also used by cement manufacturing industries. Roller mills are used for the transport of slabs and for wire rolling mills.
In addition, there are four applications of gears that are particularly emblematic, and which are implemented in countless sectors and fields:

Question 10) Describe all the characteristics of gears?

Answer 10)

Characteristics of Gears by Type

Note: If applicable, “A” indicates advantageous characteristics and “D” indicates disadvantageous characteristics
Type of Gear	Characteristics
Spur	Most common type of gear Circular gear body Straight teeth cut or inserted parallel to the gear’s shaft Used for parallel axes configuration Mated with spur gears, internal gears, or gear racks High precision and efficiency (A) Easy to manufacture (A) Does not produce thrust force (A) Capable of handling high speed and high loads (A) Gear teeth experience high stress due to tooth design (D) Noise production during high speeds (D)
Helical	Circular gear body Teeth twisted at an angle around gear body Used for parallel axes configuration Available in right-hand and left-hand designs Available in single and double helical designs Gradual tooth engagement and less impact loading (A) Quieter, smoother operation (A) Capable of handling greater loads (A) Lower efficiency (D) Higher design complexity, greater cost of manufacturing (D) Single helical design products thrust force (D), double helical does not (A)
Bevel	Cone-shaped gear body Used for intersecting axes configuration Available in straight, spiral, and Zerol® bevel tooth designs Straight: simplest bevel gear design and easiest to manufacture (A); high impact, noise level, and stress (D) Spiral: gradual tooth engagement and less impact loading, noise, and vibration (A); higher design complexity and greater cost of manufacturing (D) Zerol®: Quieter and smoother than straight bevel, able to rotate in both directions unlike spiral bevel (A)
Worm	Pair comprised of a circular gear and a screw-shaped gear Used for non-parallel, non-intersecting axes configuration Large gear ratios and gear reduction (A) Quiet, smooth operation (A) Self-locking mechanism (A) Low transmission efficiency (D) Large amounts of friction (D)
Rack and Pinion	Pair comprised of a gear rack and cylindrical gear Used for parallel axes configuration Rack mated with spur or helical gear Converts rotational motion to linear motion or vice versa Simple design, easy to manufacture (A) Capable of handling greater loads (A) Transmission cannot continue infinitely in one direction (D) Large amount of backlash between mated teeth (D) Gear teeth experience high friction and stress due to tooth design (D)

Sign Up