undefined | unit 5 80386 microprocessor

Back to Study material

MICRO

Unit 5

80386 Microprocessor

Q1) Explain the features of 80386 Microprocessor?

A1)

It is a 32-bit microprocessor. Thus has 32-bit ALU.

80386 has data bus of 32-bit.

It holds address bus of 32 bit.

It supports physical memory addressability of 4 GB and virtual memory addressability of 64 TB.

80386 supports variety of operating clock frequency, which are 16 MHz, 20 MHz, 25 MHz and 33 MHz.

It offers 3 stage pipeline: fetch, decode and execute. As it supports simultaneous fetching, decoding and execution inside the system.

Q2) What is 80386 used for?

A2) 80386 microprocessors was designed by Intel in October 1985 which is an upgraded version of 80286 microprocessor. It is a 32-bit processor that can carry out 32-bit operation in one cycle. It has data and address bus of 32-bit each.

The 80386 is a 32-bit microprocessor optimized for multitasking operating systems and designed for applications needed for high performance.

The 32-bit registers and data paths support 32-bit addresses and data types. The processor can address up to four gigabytes of physical memory and 64 terabytes (2^(46) bytes) of virtual memory.

The on-chip memory-management facilities include address translation registers, advanced multitasking hardware, a protection mechanism, and paged virtual memory.

Special debugging registers provide data and code breakpoints even in ROM-based software.

Q3) Explain the memory system of 80386?

A3) The physical memory system of the 80386 is 4G bytes in size .If virtual addressing is used, 64T bytes are mapped into 4G bytes of physical space by the memory management unit and descriptors.

Figure shows the organization of the 80386 physical memory system.

The memory is divided into four 8-bit wide memory banks, each containing up to IG bytes of memory.

This 32-bit wide memory organization allows bytes, words, or double words of memory data to access directly.

The 80386 transfers up to a 32-bit wide number in a single memory cycle, whereas the early 8088 requires four cycles to accomplish the same transfer, and the 80286 and 80386SX require two cycles.

The data width is important, especially with single-precision floating-point numbers that are 32 bits wide. High-level software normally uses floating-point numbers for data storage, so 32-bit memory locations speed the execution of high level software when it is written to take advantage of this wider memory.

In the 80386DX, the memory banks are accessed via four bank enable signals. This arrangement allows a single byte to be accessed when one bank enable signal is activated by the microprocessor.

It also allows a word to be addressed when two bank enable signals are activated. In most cases, a word is addressed in bank 0 and l or in bank 2 and 3.

The Memory location 00000000H is in bank 0, location 0000000IH is in bank 1, location 00000002H is in bank 2, and location 00000003H is in bank 3.

The memory system for 80386

Q4) Explain the architecture of 80386?

A4) The figure below shows the architectural representation of 80386 microprocessor:

Basically it has 6 functional units which are as follows:

Bus Interface Unit

Code Fetch Unit

Instruction Decode Unit

Execution Unit

Memory Management Unit

As we have already discussed that the 80386 possess the ability of 3 stage pipelining thus performs fetching, decoding and execution simultaneously along with memory management and bus accessing. Thus all these units operate parallely.

This pipelining technique leads to reduction in overall processing time thereby increasing the performance of the overall system.

Let us now move further and understand the operation of each unit in detail.

1. Bus Interface Unit

The bus interface unit or BIU holds a 32-bit bidirectional data bus as well as 32-bit address bus. Whenever a need for an instruction or a data fetch is generated by the system then the BIU generates signals (according to the priority) for activating the data and address bus in order to fetch the data from the desired address.

The BIU connects the peripheral devices through the memory unit and also controls the interfacing of external buses with the coprocessors.

2. Code Prefetch Unit

This unit fetches the instructions stored in the memory by making use of system buses. Whenever the system generates a need for an instruction then the code prefetch unit fetches that instruction from the memory and stores it in 16-byte prefetch queue.

So to speed up the operation this unit fetches the instructions in advance and the queue stores these instructions.

The sequence in which the instructions are fetched and gets stored in the queue depends on the order they exist in the memory.

As this unit fetches one double word in single access. So, in such a case, it is not necessary that each time only a single instruction will be fetched, as the fetched instruction can be parts of two different instructions.

It is to be noted here that, code prefetching holds lower priority than data transferring. As whenever, a need for data transfer is generated by the system then immediately the code prefetcher leaves the control over the buses. So that the BIU can transfer the required data.

But prefetching of instruction and storing it in the queue reduces the wait for the upcoming instruction to almost zero.

3. Instruction Decode Unit

We know that instructions in the memory are stored in the form of bits. So, this unit decodes the instructions stored in the prefetch queue. Basically the decoder changes the machine language code into assembly language and transfers it to the processor for further execution.

4. Execution Unit

The decoded instructions are stored in the decoded instruction queue. So, these instructions are provided to the execution unit in order to execute the instructions.

The execution unit controls the execution of the decoded instructions. This unit has a 32-bit ALU, that performs the operation over 32-bit data in one cycle. Also, it consists of 8 general purpose as well as 8 special purpose registers. These are used for data handling and calculation of offset address.

5. Memory Management Unit

This unit has two separate units within it. These are

Segmentation Unit and

Paging Unit

Segmentation unit: The segmentation unit plays a vital role in the 80836 microprocessor. It offers protection mechanism in order to protect the code or data present in the memory from application programs.

It gives 4 level protection to the data or code present in the memory. Every information in the memory is assigned a privilege level from PL0 to PL3. Here, PL0 holds the highest priority and PL3 holds the lowest priority.

Suppose a file (either data or code) is needed to be accessed is stored in the memory at PL0. Then only those programs which are working at PL0 would be able to access that file. While other programs will not be able to access the same.

Also, if a file is present at PL1, then programs of PL0 and PL1 both can access it. As PL0 has higher priority than PL1. So, for protection purpose the main part of OS is stored in PL0 while PL3 holds the user programs.

Providing protection to the data or code inside the system is the most advantageous factor that was first given by 80386 microprocessor.

Paging Unit: The paging unit operates only in protected mode and it changes the linear address into physical address. As the programmer only provides the virtual address and not the physical address.

The segmentation unit controls the action of paging unit, as the segmentation unit has the ability to convert logical address into linear address at the time of executing an instruction.

Basically it changes the overall task map into pages and each page has a size of 4K. This allows the handling of task in the form of pages rather than segments.

Paging unit supports multitasking. This is so because the physical memory is not required to hold the whole segment of any task. Despite, only that part of the segment which is needed to be currently executed must be stored in that memory whose physical address is calculated by the paging unit.

This resultantly reduces the memory requirement and hence this frees the memory for other tasks. Thus,we get an effective way for managing the memory to support multitasking.

Q5) Explain 80386 special function registers?

A5)

Control Registers:

CR0:

The CR0 register is 32 bits long on 80386 processor. The processor is 64 bits long. CR0 has various control flags that modify the basic operation of the processor.

Bit	Name	Full Name	Description
31	PG	Paging	If 1 enable paging and use CR3 register else disable paging
30	CD	Cache disable	Globally enable/disable the memory cache
29	NW	Not-write through	Globally enable/disable write back cache
18	AM	Alignment mask	Alignment check enabled if AM set
16	WP	Write protect	Determines whether CPU can write to pages marked read only
5	NE	Numeric error	Enable internal x87 floating point error reporting when set else enables PC style error detection
4	ET	Extension type	On 386 it allows to specify whether the external math coprocessor was an 80287 or 80387
3	TS	Task switched	Allows saving x87 task context upon a task switch only after.
2	EM	Emulation	If set no x87 floating point unit present if clear x87 FPU present.
1	MP	Monitor co-processor	Controls interaction of WAIT/FWAIT instructions with TS flag in CR0
0	PE	Protected Mode Enable	If 1 system is in protected mode else system is in real mode.

CR1

Reserved

CR2

Contains a value called Page Fault Linear Address (PFLA) . When page fault occurs the address the program attempted to access is stored in CR2 register.

CR3

Used when virtual addressing is enabled hence when PG bit is set CR0,CR3 enables the processor to translate linear addresses into physical addresses by locating the page directory and page tables for current task. Typically the upper 20 bits of Cr3 become the page directory base register which stores the physical address of the first page directory entry.

CR4

Used in protected mode to control operations such as virtual-8086 support enabling I/O breakpoints, page size extension and machine

Q6) Explain debug register?

A6) Six 80386 registers are used to control debug features. These registers are accessed by variants of MOV instruction . A debug register may be either source operand and destination operand . The debug register are privileged resources; the MOV instructions that access them can only be executed at privilege level zero. An attempt to read or write the debug registers when executing at any other privilege level causes a general protection exception.

Q7) Explain 80386 memory management?

A7) 80386 transforms logical addresses that is the addresses viewed by programmers into physical address that is actual addresses in physical memory in two steps:

Segment translation, in which a logical address consisting of a segment selector and segment offset are converted to a linear address.

Page translation, in which a linear address is converted to a physical address. This step is optional, at the discretion of systems-software designers.

These translations are performed in a way that is not visible to applications programmers.

The Figure illustrates the two translations at a high level of abstraction.

Q8) What are the steps involved for translation?

A8) To perform this translation, the processor uses the following data structures:

- Descriptors

- Descriptor tables

- Selectors

- Segment Registers

Descriptors

The segment descriptor provides the processor with the data it needs to map a logical address into a linear address. Descriptors are created by compilers, linkers, loaders, or the operating system, not by applications programmers. The Figure illustrates two general descriptor formats.

All types of segment descriptors take one of these formats. Segment-descriptor fields are:

BASE: It defines the location of segment within the 4- gigabyte linear address space. The processor concatenates three fragments of the base address to form a single 32-bit value.

LIMIT: Defines the size of the segment. When the processor concatenates the two parts of the limit field, a 20-bit value results. The processor interprets the limit field in one of two ways, depending on the setting of the granularity bit:

In units of one byte, to define a limit of up to 1 megabyte.

In units of 4 Kilobytes, to define a limit of up to 4 gigabytes. The limit is shifted left by 12 bits when loaded, and low-order one-bits are inserted.

Granularity bit: Specifies the units with which the LIMIT field is interpreted. When the bit is clear, the limit is interpreted in units of one byte; when set, the limit is interpreted in units of 4 Kilobytes.

TYPE: Distinguishes between various kinds of descriptors.

DPL (Descriptor Privilege Level): Used by the protection mechanism

Segment-Present bit: If this bit is zero, the descriptor is not valid for use in address transformation; the processor will signal an exception when a selector for the descriptor is loaded into a segment register.

The Figure shows the format of a descriptor when the present-bit is zero. The operating system is free to use the locations marked AVAILABLE. Operating systems that implement segment-based virtual memory clear the present bit in either of these cases:

When the linear space spanned by the segment is not mapped by the paging mechanism.

When the segment is not present in memory.

Accessed bit: The processor sets this bit when the segment is accessed that is a selector for the descriptor is loaded into a segment register or used by a selector test instruction. Operating systems that implement virtual memory at the segment level may, by periodically testing and clearing this bit, monitor frequency of segment usage.

Creation and maintenance of descriptors is the responsibility of systems software, usually requiring the cooperation of compilers, program loaders or system builders, and threating system.

Segment Translation

15 0 31 0

LOGICAL +----------------+ +-------------------------------------+

ADDRESS | SELECTOR | | OFFSET |

+---+---------+--+ +-------------------+-----------------+

+------+ ! |

| DESCRIPTOR TABLE |

| +------------+ |

| | | |

| |------------| |

| | SEGMENT | BASE +---+ |

+->| DESCRIPTOR |-------------->| + |<------+

|------------| ADDRESS +-+-+

| | |

+------------+ |

LINEAR +------------+-----------+--------------+

ADDRESS | DIR | PAGE | OFFSET |

+------------+-----------+--------------+

General Segment-Descriptor Format

DESCRIPTORS USED FOR APPLICATIONS CODE AND DATA SEGMENTS

31 23 15 7 0

+-----------------+-+-+-+-+---------+-+-----+-+-----+-+-----------------+

| | | | |A| | | | | | | |

| BASE 31..24 |G|X|O|V| LIMIT |P| DPL |1| TYPE|A| BASE 23..16 | 4

| | | | |L| 19..16 | | | | | | |

|-----------------+-+-+-+-+---------+-+-----+-+-----+-+-----------------|

| | |

| SEGMENT BASE 15..0 | SEGMENT LIMIT 15..0 | 0

| | |

+-----------------+-----------------+-----------------+-----------------+

DESCRIPTORS USED FOR SPECIAL SYSTEM SEGMENTS

31 23 15 7 0

+-----------------+-+-+-+-+---------+-+-----+-+-------+-----------------+

| | | | |A| | | | | | |

| BASE 31..24 |G|X|O|V| LIMIT |P| DPL |0| TYPE | BASE 23..16 | 4

| | | | |L| 19..16 | | | | | |

|-----------------+-+-+-+-+---------+-+-----+-+-------+-----------------|

| | |

| SEGMENT BASE 15..0 | SEGMENT LIMIT 15..0 | 0

| | |

+-----------------+-----------------+-----------------+-----------------+

A - ACCESSED

AVL - AVAILABLE FOR USE BY SYSTEMS PROGRAMMERS

DPL - DESCRIPTOR PRIVILEGE LEVEL

G - GRANULARITY

P - SEGMENT PRESENT

Descriptor Tables

wwSegment descriptors are stored in either of two kinds of descriptor table:

- The global descriptor table (GDT)

- A local descriptor table (LDT)

A descriptor table is simply a memory array of 8-byte entries that contain descriptors, as shown in figure. A descriptor table is variable in length and may contain up to 8192 (2^(13)) descriptors.

The first entry of the GDT (INDEX=0) is not used by the processor. The processor locates the GDT and the current LDT in memory by means of GDTR and LDTR registers.

These registers store the base addresses of the tables in the linear address space and store the segment limits.

The instructions LGDT and SGDT give access to the GDTR; the instructions LLDT and SLDT give access to the LDTR.

Format of Not-Present Descriptor

31 23 15 7 0

+-----------------+-----------------+-+-----+-+-------+-----------------+

| | | | | | |

| AVAILABLE |O| DPL |S| TYPE | AVAILABLE | 4

| | | | | | |

|-----------------------------------+-+-----+-+-------+-----------------|

| |

| AVAILABLE | 0

| |

+-----------------+-----------------+-----------------+-----------------+

Descriptor Tables

GLOBAL DESCRIPTOR TABLE LOCAL DESCRIPTOR TABLE

+------+-----+-----+------+ +------+-----+-----+------+

| | | | | | | | | |

|------+-----+-----+------| |------+-----+-----+------|

| | | M | | | M

+------------+------------+ +------------+------------+

| | | |

+------+-----+-----+------+ +------+-----+-----+------+

| | | | | | | | | |

|------+-----+-----+------| |------+-----+-----+------|

| | | N + 3 | | | N + 3

|------+-----+-----+------| |------+-----+-----+------|

| | | | | | | | | |

|------+-----+-----+------| |------+-----+-----+------|

| | | N + 2 | | | N + 2

|------+-----+-----+------| |------+-----+-----+------|

| | | | | | | | | |

|------+-----+-----+------| |------+-----+-----+------|

| | | N + 1 | | | N + 1

|------+-----+-----+------| |------+-----+-----+------|

| | | | | | | | | |

|------+-----+-----+------| |------+-----+-----+------|

| | | N | | | N

+------------+------------+ +------------+------------+

| | | |

+------+-----+-----+------+ +------+-----+-----+------+

| | | | | | | | | |

|------+--(UNUSED)-+------| |------+-----+-----+------|

| | | | | |

+------------+------------+ +------------+------------+

^ ^

+---------------------+ | +---------------------+ |

| GDTR |--+ | LDTR |--+

+---------------------+ +---------------------+

Selectors

The selector portion of a logical address identifies a descriptor by specifying a descriptor table and indexing a descriptor within that table. Selectors may be visible to applications programs as a field within a pointer variable, but the values of selectors are usually assigned (fixed up) by linkers or linking loaders. The format of selector is shown in figure.

Index:

It selects one of 8192 descriptors in a descriptor table. The processor simply multiplies this index value by 8 and adds the result to the base address of the descriptor table in order to access the appropriate segment descriptor in the table.

Table Indicator:

It specifies to which descriptor table the selector refers. A zero indicates the GDT a one indicates the current LDT.

Requested Privilege Level:

Used by the protection mechanism. Because the first entry of the GDT is not used by the processor, a selector that has an index of zero and a table indicator of zero which can be used as a null selector.

The processor does not cause an exception when a segment register (other than CS or SS) is loaded with a null selector. It will, however, cause an exception when the segment register is used to access memory. This feature is useful for initializing unused segment registers to trap accidental references.

Format of a Selector

15 4 3 0

+-------------------------+-+---+

| |T| |

| INDEX | |RPL|

| |I| |

+-------------------------+-+---+

TI - TABLE INDICATOR

RPL - REQUESTOR'S PRIVILEGE LEVEL

Segment Registers

16-BIT VISIBLE

SELECTOR HIDDEN DESCRIPTOR

+----------------+----------------------------------------+

CS | | |

|----------------+----------------------------------------|

SS | | |

|----------------+----------------------------------------|

DS | | |

|----------------+----------------------------------------|

ES | | |

|----------------+----------------------------------------|

FS | | |

|----------------+----------------------------------------|

GS | | |

+----------------+----------------------------------------+

Segment Registers

The 80386 stores information from descriptors in segment registers, thereby avoiding the need to consult a descriptor table every time it accesses memory.

Every segment register has a "visible" portion and an "invisible" portion, as shown in the figure . The visible portions of these segment address registers are manipulated by programs as if they were simply 16-bit registers. The invisible portions are manipulated by the processor.

Q9) Explain virtual mode 8086?

A9) The 80386 supports execution of one or more 8086, 8088, 80186, or 80188 programs in an 80386 protected-mode environment.

An 8086 program runs in this environment as part of V86 (virtual 8086) task. V86 tasks take advantage of the hardware support of multitasking offered by the protected mode. There can be multiple V86 tasks, each one executing an 8086 program, but V86 tasks can be multi-programmed with other 80386 tasks.

The purpose of a V86 task is to form a "virtual machine" with which to execute an 8086 program. A complete virtual machine consists not only of 80386 hardware but also of systems software. Thus, the emulation of an 8086 is the result of cooperation between hardware and software:

The hardware provides a virtual set of registers via the TSS, a virtual memory space and directly executes all instructions that deal with these registers and with this address space.

The software controls the external interfaces of the virtual machine in a manner consistent with the larger environment in which it executes. In the case of I/O, software can choose either to emulate I/O instructions or to let the hardware execute them directly without software intervention.

Software that helps implement virtual 8086 machines is called a V86 monitor.

Q10) Explain protected mode addressing?

A10) Protected mode memory addressing 80286 and above allows access to data and programs located above the first 1M byte of memory and within the first 1M byte of memory.

Addressing this extended section of the memory system requires a change to the segment plus an offset addressing scheme used with real mode memory addressing.

When data and programs are addressed in extended memory, the offset address is still used to access information located within the memory segment.

In place of the segment address, the segment register contains a selector that selects a descriptor from a descriptor table. The descriptor describes the memory segment’s location, length, and access rights.

Because the segment register and offset address still access memory, protected mode instructions are identical to real mode instructions.

Most programs written to function in the real mode will function without change in the protected mode. The difference between modes is in the way that the segment register is interpreted by the microprocessor to access the memory segment.

Another difference, in the 80386 and above, is that the offset address can be a 32-bit number instead of a 16-bit number in the protected mode. A 32-bit offset address allows the microprocessor to access data within a segment that can be up to 4G bytes in

Q11) Explain memory paging mechanism?

A11) Intel386Dx uses two level table mechanism to convert linear address to physical address.

The components in paging mechanism are:

- Page Directory

- Page table

- Page frame

The page size of Intel 80386 is 4KB.

Page Descriptor Base Register

CR2 is used to store the 32-bit linear address of page fault.

CR3 – Page Directory Physical Base Address Register which stores the physical starting address of Page Directory.

The lower 12 bits of CR3 are always zero to ensure that the Page Directory is always page aligned.

Loading it via a MOV CR3,reg instruction causes Page Table Entry cache to be flushed and a task switch through TSS changes the value of CR0.

Page Directory:

It is 4KB in size and allows up to 1024 entries are allowed

The upper 10 bits of the linear address are used as index to corresponding page directory entry.

Page directory entry points to page tables.

Each Page table is 4K bytes and holds up to 1024 Page Table Entries(PTE)

PTEs contain the starting address of the page frame and statistical information about the page.

The 20 upper-bit page frame address is concatenated with lower 12 bits of the linear address to form the physical address.

Page tables can be shared between tasks and swapped to disks

Page Table Entry

P(Present) Bit : which indicates if PDE/PTE can be used in address translation . P-bit currently executed page is always high.

A(Accessed) Bit : It is set before any access to the page.

D(Dirty) bit : It is set before a write operation to the page is carried out. The D bit is undefined for PDEs.

OS Reserved Bits: They are defined by the operating system software.

U/S (0-> Supervisor 1-> User bit ) and R/W (0-> Read , 1-> Write ) ;

They are used to provide page level or page table level protection. They are decoded as

Supervisor level(U/S=0) for operating system and other system software and related data.

User level (U/S=1) -for application procedures and data.

Read only access (R/W =0)

Read/write access (R/W=1)

(R/W , U/S bits )

The paging mechanism distinguishes between two levels of protection.

User -which corresponds to level 3 of the segmentation-based protection

Supervisor which encompasses all the other protection levels(0,1,2)

Programs executing at Level 0,1 or 2 bypass the page protection

Segmentation based protection I still enforced by hardware.

Sign Up